Venus Enterprises

General purpose epoxy bonding agent Uses Bonding old and new cementitious substrates. Advantages ?? Can be applied on concrete & mortar substrate ?? Facilitates improvement in mechanical strength ?? Good positive adhesion Description Nitobond EP Std is a two component epoxy bonding agent supplied in pre-weighed quantities for ready on-site mixing and use. Technical Support The company provides a technical advisory source supported by a team of specialists in the field. Properties Pot life Min. 120 minutes @ 350 C Full hardness 24 hrs. Full Cure 7 days Overlay time Upto 3 hrs. Compressive Strength 40 N/mm2 BS 6319 Part 2 Tensile Strength 15 N/mm2 BS6319 Part 7 Flexural Strength 25 N/mm2 BS 6319 Part3 Bond strength ASTM C881 11N/mm2 Below 200 C, above mentioned times will increase. Application Instructions Preparation All surfaces to be treated must be sound, dust-free and clean. All laitence should be removed by wire-brushing or any other suitable means. Surfaces contaminated with oil or grease, shall be cleaned thoroughly to remove such contaminants.

UltraTech Seal & Dry 5 PLUS is an Acrylic Polymer based multipurpose bonding agent. Packaging 1 Kg, 5 Kg, 10 Kg, 20 Kg Shelf Life UltraTech Seal & Dry 5 PLUS has a shelf life of 18 months from the date of manufacture. Store at cool and dry place. Safety Directions UltraTech Seal & Dry 5 PLUS is non-toxic. Use of gloves and goggles recommended. Any splashes to the skin or eyes should be washed off with clean water. In case of prolonged irritation, medical advice should be sought. UltraTech Seal & Dry 5 PLUSis non-flammable. Other Product Categories available with UltraTech Building Products Division   Tile Adhesives   Micro Concrete and Repair Product   Industrial/Precision Grout and Anchors   Injection Grouting Material   Plasters and Jointing Mortar   Floor Screeds   Autoclaved Aerated Lightweight Concrete Blocks ULTRATECH UltraTech Cement Limited (Building Products Division) 30214100/4400 DISCLAIMER Information provided on this data sheet is the guideline for usage. Users are advised to undertake a trial for product suitability prior to it’s full scale usage. There is no implied guaranty/warranty for the results and the company is not liable for any consequential damages. DIRECTIONS FOR USE Mix Ratio - Seal & Dry 5PLUS : Grey Cement Mix Ratio - Seal & Dry 5PLUS : White Cement Coverage / kg Note:- • The adhesion strength between concrete / plaster and reinforcement is not hampered by using UltraTech Seal & Dry 5 PLUS. Anticorrosive Rebar Coating 1:1.5 75 RMT @ 1mm thickness for 10mm dia Bar. Crack Filling Tile Joint Filling Priming / Key Coat (50% water by wt) 100 ml per 1 kg of white cement 250 RMT @ (2mm X 6mm Tile Joint) 1:0.5 1:0.5 75 Sft/Kg in single film coat As a waterproofing coat   Apply mix of Ultratech Seal and Dry SBR with grey cement in the ratio as per the table given on next page. Application Solid content : 50% +- 1% by weight in the solution PH value : 7 to 8   Easy and simple to use.   Provides excellent water impermeability.   Ensures good workability.   Provides good bonding and adhesion.   Provides toughness and flexibility.   Excellent material for repair and renovation. Description 50 ml per 1 kg of white cement 85 RMT @ (6mm X 6mm "V" Groove) Waterproofing 1:3:8 (S&D 5 Plus, Water & Cement) 100 Sft/Kg @ 1mm Thickness Areas of Application UltraTech Seal & Dry 5 PLUS is recommended for standard / general waterproofing of bathrooms, sunken areas, terrace and water tanks. It is recommended for crack filling and tile joint filling by mixing along with white cement. It can be used by mixing with water, directly as a priming/key coat over plastered surfaces and putty before painting to cover the minor surface shrinkage cracks. UltraTech Seal & Dry 5 PLUScan also be used as an anti -corrosive protection coating over new and old reinforcements.   Prepare the surface by removing oil, bond inhibiting agents, dirt, dust and laitance.   Clean the surface with wire brush/water jet/mopping.   Wet the surface with water and bring it to Surface Saturated condition   Corroded reinforcement bars should be exposed, cleaned and treated with an anti corrosive product

JSW Tylfix Type 1 Pro is a polymer-modified, grey cement-based thin-set tile adhesive for fixing high porosity(greater than 3%) tiles like ceramic/ clay of regular size (size not more than 300 mm X 300 mm). It is suitablefor both vertical and horizontal surfaces, over the cementitious substrate for indoor applications in dry areas.It also recommended for installation of vitrified tiles on the floor.

Bonding segmented concrete bridges to speed up construction and provide a structural and water resistant joint. Can be used for pointing Stone masonry joints to retain structural integrity . Advantages „ Excellent squeezability „ High bond strength „ Fast cure „ Tolerant to damp surfaces „ Wide range temperature applications Standards compliance Nitobond PC meets the FIP specifications in all respects. Description Nitobond PC thixotropic epoxy adesive is a 2 pack solvent free epoxy resin system consisting of a white base, black hardener in preweighed quantities for easy onsite mixing. The product is available in three grades :

it id a single component white emulsion which is based on modified acrylic copolymers. it is formulated to be used as a bonding agent for cementitious mortars, microcrete and cement plasters. The product is ready to use, has excellent adhesion characteristics and delelops a tenacios bond of the new mortar / plaster / micro crete to the host concret.

We are reckoned entity of this domain engaged in offering an enhanced quality Epoxy Bonding Adhesive.

Choksey FixGuruu Futura- 5 FA 06 Semi White & Light(0 Reviews)

FUTURA-5 PLus is an Acrylic based highly elastomeric waterproof coating. After drying it forms a film of exceptional strength & flexibility that prevents peeling, fungi / algae growth, future cracks & water seepage. Having upto 250 – 300% elongation property & crack bridge property up to 1 mm.

FEATURES/ADVANTAGES

• Prevents growth of fungus, moss, etc.
• Durable & economical
• Remarkable elasticity & resilience for substrate's thermal expansion & contraction
• Optimized rheology for high film build
• Breath ability for preventing moisture in walls & roofs (MICROPOROUS)
• Can be applied on damp surfaces
• Excellent alkali resistance
• Resistance to chalking & flaking
• UV resistant for outstanding durability
• Available in attractive shades
• DFT in 2 coats is 110 micron

APPLICATION AREAS

• Facades
• External walls
• Exterior RCC surface
• Masonry walls or facades
• Stone walls
• Asbestos
• China mosaic tiles
• Sloping roofs comprising system of primer coat + 1 coat of Futura-5 + Polyester mat (thickness of 55-70 gsm)+2 coats of Futura-5+

MCON Bond URP is a styrene butyl rubber-based bonding agent formulated from selected synthetic copolymers. It is designed for structural repairs, providing a strong bonding coat to protect and repair reinforced concrete (RCC) and steel structures.

MCON Super Hack is a single-component liquid bonding agent for plaster that strengthens the bond between plaster and concrete, eliminating the need to hack concrete surfaces before plastering. 

An acrylic-based bonding agent specially engineered for concrete cold joints, plaster, and gypsum applications. It combines high strength and flexibility, ensuring durable and water-resistant bonds. With a pull-off adhesion strength of 1.7 N/mm², ColdBond is ideal for creating monolithic joints that stand the test of time.

TerraSil is designed to be utilised with ZycoBond - a UV and heat stable, crosslinkable soil modifier that chemically binds soil particles together into a flexible crosslinked network. Chemical binding and nano size of the polymer leads to improved load bearing capacity and flexibility of the soil base.ZycoBond is a 80 - 90 nm flexible acrylic co-polymer that has a very high surface area available for bonding. The higher number of contact points ensure flexible bonding at a nano level, leading to improved fatigue resistance in stabilized soils. ZycoBond in combination with TerraSil imparts higher strength and enhanced flexibility, thereby enabling dimensionally stable non-deforming bases .When TerraSil and ZycoBond are incorporated as part of the stabilized base, significant reduction in pavement thickness can be accomplished, while simultaneously enhancing the overall load bearing capacity. (3 - 5x enhancement in MSA) This is accomplished by replacing the granular sub base and Wet Mix Macadam with a waterproofed and flexibly bonded soil-aggregate layer.TerraSil and ZycoBond are mixed in situ with the soil as part of the water of compaction (OMC Water). Due to their ability to be introduced through water, the solution mixes and distributes into the soil extremely efficiently. The application as water solution helps to avoid dusting issues. Furthermore, due to the low dosage rates of TerraSil and ZycoBond, transportation costs to site are significantly reduced.Store TerraSil and ZycoBond between 5° - 45 °C (41° - 113 °F) in a shaded, dry area away from sunlight, heat, source of sparks, rain and standing water. Fasten the container lid securely after every use. Its shelf life is 48 months. In case the product freezes at low temperatures, allow it to thaw and melt.Established in 1997, Zydex is a specialty chemicals company with the purpose of innovating for sustainability. We are committed to creating a sustainable world through innovative, environment friendly and patented technologies in the areas of AGRICULTURE, TEXTILES, PAINTS & WATERPROOFING and ROADS. Our product portfolio encompasses 200+ innovative solutions with presence in over 40 countries across the globe. Sustainable Green Chemistry Zydex is deeply committed to sustainable chemistries that will ensure a greener future for everyone. Our commitment has made us a pioneer in introducing non-polluting and nonhazardous technologies that conserve, protect and enhance the environment. Pursuing innovations that would mean a greener, safer and more resource renewable world is our passion. Our technologies have been recognized for their contribution to sustainability and are accepted globally

• SELFOM B1 Fire Retardant PU Foam (Gun Grade, 750ml, 900g) is a high-performance, fire-resistant polyurethane foam.
• Designed for sealing and insulating gaps, joints, and penetrations in fire-rated structures.
• Provides excellent adhesion to concrete, brick, metal, wood, and other construction materials.
• Expands to fill cavities while offering superior thermal and acoustic insulation properties.

  

• Polygrip Hot Bond is a high-performance hot melt adhesive designed for strong and instant bonding.
• Provides excellent adhesion to materials like wood, fabric, plastic, and paper.
• Fast-setting, durable, and resistant to heat and moisture.
• Ideal for packaging, woodworking, crafts, and industrial applications.

  

UltraTech X'TRAKRETE is styrene Butadiene latex co-polymer , multi purpose bonding agent ecommended for water proofing of bathroom , sunk areas , terrace and water trank . it can be  used as modifier in motar and screed for repair of old concrect and plaster .lf strongly bonds old concreat and plaster with new concreat and plaster

Multipurpose high performance elastic polyurethane tile adhesive with no vertical slip on deformablesurfacesDESCRIPTIONSikaCeram®-428 Super Bond T is a two component,high performance, universal, elastomeric polyurethaneresin adhesive used for high adhesion fixing on deformablesurfaces with no vertical slip. It is particularlysuitable for natural stone and marble sensitive todampness and on absorbent and non-absorbent substrates.Interior and exterior use.USESSikaCeram®-428 Super Bond T may only be used by experiencedprofessionals.Fixing ceramic tiles of all types and sizes on difficultsubstrates or ones liable to warp considerably▪▪ Fixing natural stone and marble affected by humidity▪ Fixing vitreous mosaicFixing ceramic tiles to kitchen surfaces or work tops,to wood or iron surfaces▪▪ Fixing on heating screeds▪ Fixing thin and / or large tilesCHARACTERISTICS / ADVANTAGES▪ Multipurpose▪ Good workability▪ No creep▪ High performance▪ Extremely flexible▪ Highly thixotropic▪ Excellent durability▪ Resistant to ageing▪ Adhesion to most construction materials▪ Suitable for dry wall substrates▪ High deformability▪ Hardening without shrinkagePRODUCT INFORMATIONProduct declaration ▪ R2T according to EN 12004-1▪ R2T according to ISO 13007-1Chemical base Polyurethane resin and selected quartzPackaging Part A+B pre-batched 5 kg setPart A 4.6 kg containerPart B 0.4 kg containerShelf life 12 months from date of productionStorage conditions The product must be stored properly in original, unopened and undamagedsealed packaging in dry conditions at temperatures between +10 °Cand +40 °C. Protect from direct sunshine.1 / 4Appearance / Colour Part A+B mixed White pastePart A White viscous pastePart B Transparent liquidDensity Part A+B mixed ~1.60 kg/LPart A ~1.75 kg/LPart B ~1.00 kg/L(EN ISO 2811-1)All density values at +30 °C.TECHNICAL INFORMATIONTransverse deformation Highly deformable (EN 12004-2 / ISO 13007-2)Tensile adhesion strength After > 20 min open time ≥ 0.5 N/mm2 (EN 12004-2 /ISO 13007-2)Shear Adhesion Initial ≥ 2 N/mm2After water immersion ≥ 2 N/mm2After thermal shock ≥ 2 N/mm2(EN 12004-2 /ISO 13007-2)Service temperature -20 °C min. / +80 °C max.Chemical resistance Resistant to many chemicals. Contact Sika Technical Services for additionalinformation.Slip resistance ≤ 0.5 mm (EN 12004-2 / ISO 13007-2)APPLICATION INFORMATIONMixing ratio Part A : Part B = 92 : 8 (by weight)Consumption Consumption is dependent on the substrate, surface profile, roughness,size of the tiles, the joints between them and application technique (i.e.single spreading / floating method or double spreading / buttering method).Apply product to a test area to calculate the exact consumption forthe specific substrate conditions and proposed application.

SC Apcorep Interpenetrating Polymer Network (IPN) Coating System is a novel type of polymer formulation consisting of more than two polymers cross linked in the network form by synthesis. The morphology studies conducted at CBRI, Roorkee using Scanning Electron Microscopy & Differential Scanning Calorimetry have proved the efficacy of IPN System with respect to Chemical Resistance, Weather Resistance, Tensile Strength, Flexibility, Shear Strength & Hardness Properties. RECOMMEND

Ascolite Ascobond Latex is a high-performance waterproofing additive and multipurpose adhesion enhancer designed to improve the durability, strength, and bonding of cementitious materials. This white fluid latex is commonly used in construction applications such as plastering, rendering, screeding, and concrete repairs.