Venus Enterprises

which mixes readily with water in any proportions.  It is based on internationally recognised chemicals  and is free  from calcium  chloride  and  similar  salts. Technical support Fosroc  offers technical support service to specifiers, end users and contractors, as well as on-site technical assistance in locations all over the country. Properties Specific gravity: 1.005 to 1.015 g/cc Chloride content : Nil Compatibility with cements :  Can be used with any type of Portland, Super Sulphate, Blast furnace or Pozzolanic cements. Setting time :  There is no significant effect on the setting of sand/cement mortars. Cebex  112 Plasticising action :  Cebex 112  entrains a  controlled amount of microscopic air bubbles which increase cohesion and provide lubrication to the sane particles in the mix, thereby imparting improved workability to the mortar.  The air bubbles hold the cement/water matrix at the contact surfaces which results in improved bond strengths. Frost resistance :  Where this is a  consideration, that air entrainment appreciably increases the frost resistance of the fully cured mortar and also improves that of fresh mortar, as established by international practice. Increased yield :  The special action of Cebex 112  causes the cement particles to disperse evenly throughout the mix, which combined with its air entrainment property, expands the volume of the mortar.  Increase in yield for the same quantities of sand and cement is typically between 8% and 18%, depending upon the coarseness or fineness of the sand used. With typical mixes of 1:3 and 1:4 cement : sand, the cost of Cebex 112 will normally be recovered and, in most cases, a net cost saving will be obtained, as a result of the increased yield.

Atactic Poly Propylene (APP) modified bituminous membrane with PE foil and flexible at -2 °C (Formerly Sika® WP Shield-103 P) DESCRIPTION SikaShield® P24 PE IN 3 mm is an APP modified bituminous waterproofing membrane with a thickness of 3 mm. It is reinforced with a non-woven polyester fabric and is flexible at -2 °C. The top surface is coated with polyethylene foil, which ensures the bond of the overlying layer. The underside of the product has a burn-off film for easy torch-application. USES The product is used as a waterproofing membrane for: Balconies and terraces under a heavy protection layer such as tiles or gravel. ▪ Flat and sloping roofs under protective layers or ballast ▪ ▪ Car park decks ▪ Bridge decks under asphalt wearing layer ▪ Underpass and subways ▪ Basements and other below ground structures Horizontal reinforced concrete slabs, decks, podiums and protrusions ▪ ▪ Vertical reinforced concrete walls The product is used as a: ▪ Base sheet and/or top sheet in multi-layer systems Please note: The product is not suitable for roofs permanently exposed to UV radiation. Protect membrane with a suitable protection layer. ▪ CHARACTERISTICS / ADVANTAGES ▪ Fully bonded ▪ Long term flexibility ▪ Excellent water tightness Very good mechanical properties (tensile, tear, shear) ▪ ▪ Can be handled in warmer temperatures easily ▪ Low water absorption ▪ Easy to install by torching method Capable of withstanding thermal and structural stresses ▪ Good durability and performance under long term ageing ▪ PRODUCT INFORMATION Chemical base Composition APP modified bitumen Reinforcing material Non-woven polyester fabric Packaging Roll width 1.0 m Roll length 10.0 m (EN 1848-1) Shelf life 12 months from date of production Storage conditions The product must be stored in original unopened and undamaged packaging in dry conditions and temperatures between +5 °C and +35 °C. Store in a vertical position. Do not stack pallets of the rolls on top of each other, or under pallets of any other materials during transport or storage.

SikaShield® P22 PE IN 3 mm is an APP modified bituminous waterproofing membrane with a thickness of 3 mm. It is reinforced with a hybrid composite reinforcement fabric and is flexible at 2 °C. The top surface is coated with polyethylene foil, which ensures the bond of the overlying layer. The underside of the product has a burn-off film for easy torch-application. USES The product is used as a waterproofing membrane for: Balconies and terraces under a heavy protection layer such as tiles or gravel. ▪ Flat and sloping roofs under protective layers or ballast ▪ ▪ Car park decks ▪ Bridge decks under asphalt wearing layer ▪ Underpass and subways ▪ Basements and other below ground structures Horizontal reinforced concrete slabs, decks, podiums and protrusions ▪ ▪ Vertical reinforced concrete walls

Mcon Ready Mix Plaster is a factory-prepared, blend of carefully graded fine sand, cement, and performance-enhancing additives, designed to provide superior workability, excellent adhesion, and a smooth finish. It is ideal for both internal and external plastering on brickwork, blockwork, and concrete surfaces.

This dry mix plaster eliminates the need for on-site mixing, ensuring consistent quality, reduced labor costs, and faster application. Simply mix with water at the site and apply directly on the surface.

Sikagard®-63 Chemical resistant epoxy protective coating DESCRIPTION Sikagard®-63 is a solvent free, two part, total solid, coloured epoxy resin based high build thixotropic protective coating with high chemical resistance. It can be used on many types of structures or elements such as cementitious, metallic and epoxy resin binder substrates. The chemical resistant properties provide surface protection from aggressive chemicals that can cause rapid degradation. USES Chemical resistant protective coating on: ▪ Concrete ▪ Stone ▪ Cementitious mortars ▪ Renderings ▪ Epoxy cement ▪ Epoxy resin-based products ▪ Steel Chemical resistant protective lining for: ▪ Silos ▪ Bund linings ▪ Chemical mixing tanks ▪ Chemical containment tanks ▪ Fuel and oil tanks ▪ Sludge tanks ▪ Industrial chemical areas ▪ Sewage, effluent and waste water treatment Anti-corrosion coating on steel elements within: ▪ Food processing plants ▪ Sewage treatment works ▪ Chemical and pharmaceutical facilities ▪ Beverage facilities CHARACTERISTICS / ADVANTAGES ▪ Good chemical resistance ▪ Good temperature resistance ▪ Good abrasion resistance ▪ Solvent free ▪ Low VOC emissions ▪ High build ▪ Impervious to liquids ▪ Easy to mix ▪ Applied by brush, roller or airless spray

For filling blow holes, making good slightly damaged concrete, eliminating minor irregularities on floors and walls prior to applying Nitoflor and Nitocote epoxy coatings. Advantages „ Easy to apply and finish „ Consistency can be adjusted by varying the filler content „ Non-slump, can be applied to vertical surfaces and trowelled into blow holes „ Reduces consumption of subsequent coatings „ Chemical resistant „ Good adhesion to concrete and steel surfaces „ Cures without shrinkage „ Available in a wide range of colors Description Nitocote VF is a thixotropic, solvent free, three component compound based on epoxy resins, graded fillers and thixotropic agents. It is applied directly to concrete for filling cracks, blow holes etc., which cures to a surface ready for subsequent coatings. Technical support Fosroc offers a technical support service to specifiers, end users and contractors, as well as on-site technical assistance in locations all over the country. Properties Density : 1.6 g/cc Volume solids : 100% Minimum application temperature : 100C Compressive strength : 50N/mm2 Pot life : 40 min at 250 C Drying time : 8 hrs at 300 C Recoatable : 24 hours Full cure : 7 days at 300 C Application instructions Surface preparation Steel : Sand blasting to SA 2 ½ , clean and dry. Concrete : Clean, dry, should be free from laitance, sand blasting or mechanical wire brushing may be necessary. Mixing Using a slow speed drill with a suitable mixing paddle, mix base, hardener components and add the filler in small quantities to get the required consistency. It is important that all the components are intermixed thoroughly. Application Due to the easy workability of the product, a variety of instruments such as trowel, scraper, filling knife can be used. After mixing, material can be taken directly from the can, or subdivided on to spot boards for individual applications. Tool cleaning Clean the tools immediately after use before the material cures. Use Nitoflor Sol for cleaning the tools. Cured material can only be removed mechanically. Limitations Nitocote VF is not suitable for application below 100 C and above 400 C. Cured Nitocote VF is not suitable for subzero temperatures. Estimating Packaging Nitocote VF 1/2 and 1 litre packs Nitoflor Sol 1, 5 and 20 litre cans Coverage and yield Nitocote VF will be consumed at a rate of 1m2 at 1mm/litre thickness. Depending on the substrate conditions the coverage may vary. Storage Shelf life 12 months in unopened containers when stored under normal warehouse conditions.

High strength, abrasion resistant epoxy reinstatement mortar. Uses Nitomortar S is used for the fast and permanent reinstatement of concrete, particularly where high strength, abrasion resistance and chemical resistance are required. The product is designed for horizontal use but can be applied vertically, although generally in thinner sections. It is ideally suited for acid tanks, sea walls, industrial fl oors and for use as a bedding mortar. Nitomortar S can be used for emergency repairs where fast strength gain is important. When properly compacted, the mortar is highly impermeable. In certain instances, Nitomortar S can be used on metal substrates. Contact the local Fosroc offi ce for advice in this respect. Advantages  High ultimate strength - Suitable for structural use  Early development of strength Minimises disruption  Abrasion resistance - Suitable for heavy traffi c areas  Highly resistant - To a wide range of chemicals  Will cure under damp conditions - Cured product is highly impermeable to water  Typically twice as strong as good quality concrete  Pre-weighed components ensure consistency Description Nitomortar S is based on a high quality solvent-free epoxy resin system. The special silica aggregates provide high strength and excellent abrasion resistance. Nitomortar S is a three - component material supplied in pre-weighed quantities ready for on-site mixing and use. 

The high elasticity, excellent bond and low water permeability of Nitoproof 750 make it ideal for a wide range of water/vapour proofing applications such as foundations, basements, tunnels, ground floors, suspended floors, roof terraces, balconies, patios, bridges, inspection pits, sewage works and inverted roofs. Advantages  Class III membrane - High elongation (>300%)  Pitch free formulation  Non-staining  Readily applied direct from can - (no mixing required)  Cures to give permanently flexible resilient barrier over a wide range of temperatures  Excellent build properties enable application to both horizontal and vertical surfaces  Can be applied to a wide range of substrates  Outstanding barrier properties ensure protection against corrosive soil conditions  Root resistant  Irreversible chemical cure eliminates melting and flow at high temperature  Excellent resistance to embrittlement Standards Compliance Nitoproof 750 has been tested by CSIRO to the requirements of AS/NZS 4654.1:2012 Waterproofing membranes for external above-ground use Part1:Materials; CSIRO test report SW8554. Copies of the test reports are available from the Fosroc website. Description Nitoproof 750 is a single-component polyurethane liquid which cures by reaction with atmospheric moisture to give a tough elastomeric waterproof membrane. It is supplied as a thixotropic liquid which is easily applied at the recommended thickness to both vertical and horizontal surfaces

TECHSEAL RDL 941 EH (BS-5212) are two component sealant based on THIOKOL – Polysulphide liquid elastomer. It consists of a ‘base’ compound and accelerator (curing agent). When two components are mixed together prior to application, a chemical reaction is initiated which cures instantly to a firm, flexible rubber like seal with excellent adhesion to concrete, masonry, wood, glass, acrylic and PVC plastics. It is capable of withstanding repeated extension, compression & cyclic movements without the loss of adhesion and resists deterioration by weathering, sunlight, ozone, water, salt, oils and fuels. It is far superior to all the conventional joint sealant material like bitumen, mastics, metallic channels and expansion sheets. Techseal RDL 941 EH is a pouring grade material used for sealing of horizontal joints. FEATURES / ADVANTAGES  Cures at ambient temperatures to a tough, elastic and flexible rubber like material  Bonds strongly to most of the building material with the use of recommended primer  Durable, remains unaffected by UV rays, ozone and weathering conditions  Resists water, salt water, 10% dil. acids except nitric acids, alkalis, most of the common chemicals, vegetable, lubricants, oils and fuels  It performs well in a temperature range intermittent from –40⁰C to 80⁰C   Slip resistant (sag) can be applied in a horizontal joint  Movement capability – Provides satisfactory hermetic sealing of the joint subjected to expansion, contraction, vibration and cyclic movement within the following limits. - Movement joints upto + 25% of the width  Resilient recovers the original width after expansion & contraction without loosing the surface bond  Excellent reparability property  It can be over coated by waterproofing compounds  Non toxic  Sealants will not cause staining to concrete masonry or stones  Fuel Resistance  Fire Resistance TYPICAL APPLICATION  Sealing of expansion, contraction & construction joints in structure such as, concrete pavement, highways, runways, airfields, and petrol pumps.  Areas, which are affected by fuel, oil, fire etc.  Extreme temperature regions.  Sealing of water retaining structure joints such as, water tank, reservoir, aqua ducts, canals, culverts and water treatment plant. 

Ultratech Readiplast Projekt is a ready-mix cement plaster/render designed for efficient and easy application on various surfaces, including RCC, stone walls, and brick walls. It's particularly suited for plastering up to 12mm thick in a single layer. Here's a more detailed description:

• Ready-mix formulation: This means you don't need to mix cement, sand, and other components yourself, saving time and effort compared to traditional plastering methods. 
• Wide application: It can be used on various surfaces like RCC, stone walls, brick walls, and concrete surfaces. 
• Single-layer application: Ideal for walls requiring a plaster thickness of up to 12mm. 
• Improved quality and durability: Readiplast is formulated with special binders and polymers, resulting in a strong, water-resistant plaster with fewer chances of cracking. 
• Ease of use: It provides a smooth surface for tiling and is convenient and easy to use. 
• Workplace cleanliness: Readiplast helps maintain a cleaner workspace during application. 
• Coverage: A 40kg bag covers approximately 18-20 sq ft when applied at a 12mm thickness. 
• Shelf Life: It has a shelf life of 6 months when stored in a cool, dry place. 
• Technical Data: It's recommended to allow a minimum of 7 days for subsequent usage after applying Readiplast. 

DESCRIPTION SikaShield® P24 PE IN 3 mm is an APP modified bituminous waterproofing membrane with a thickness of 3 mm. It is reinforced with a non-woven polyester fabric and is flexible at -2 °C. The top surface is coated with polyethylene foil, which ensures the bond of the overlying layer. The underside of the product has a burn-off film for easy torch-application. USES The product is used as a waterproofing membrane for: Balconies and terraces under a heavy protection layer such as tiles or gravel. ▪ Flat and sloping roofs under protective layers or ballast ▪ ▪ Car park decks ▪ Bridge decks under asphalt wearing layer ▪ Underpass and subways ▪ Basements and other below ground structures Horizontal reinforced concrete slabs, decks, podiums and protrusions ▪ ▪ Vertical reinforced concrete wallsThe product is used as a: ▪ Base sheet and/or top sheet in multi-layer systems Please note: The product is not suitable for roofs permanently exposed to UV radiation. Protect membrane with a suitable protection layer. ▪ CHARACTERISTICS / ADVANTAGES ▪ Fully bonded ▪ Long term flexibility ▪ Excellent water tightness Very good mechanical properties (tensile, tear, shear) ▪ ▪ Can be handled in warmer temperatures easily ▪ Low water absorption ▪ Easy to install by torching method Capable of withstanding thermal and structural stresses ▪ Good durability and performance under long term ageing

Cross LAMINATED SBS SELF ADHESIVE WATERPROOFING MEMBRANE Description Dr. Fixit Samshield XL is a SBS self adhesive waterproofing membrane based on a tropical grade of polymer modified bitumen. The bitumen compound is laminated onto an impervious, non-perforated, HDPE Valeron® film. The membrane is protected on the self adhesive side with a silicone coated release film. Typical Applications Dr. Fixit Samshield XL used as waterproofing and damp proofing intended for concrete protection. It may be used for horizontal and vertical application and as a damp proofing course for tanking below ground structures, subways, retaining walls etc. } Features } Specially formulated for tropical climate grade. } } } Provides protection against water and vapour. } Self adhesive, requires just peeling off the silicone film and sticking to the surface. } } } Excellent adhesion to vertical and horizontal surfaces. } Excellent resistance to chlorides, sulphates, alkalis and acids. } } } Good tear and puncture resistance. } Excellent tensile strength. Method of Application Application procedure may vary slightly depending upon site conditions. The general recommended guidelines for the application of the self adhesive waterproofing system are as follows: 1 SURFACE PREPARATION The surface shall be cleaned thoroughly of all contaminants like dust, traces of curing compound, oil and grease. All surface imperfections, protrusions, structurally unsound and friable concrete must be removed and repaired with a suitable concrete repair mortar. 2 PRIMING Apply Dr. Fixit Torchshield Primer @ 4-6 sq.mtrs./litre to a clean, smooth and dry surface by brush or roller. Allow the primer to dry prior to the application of the membrane. As the viscosity of the primer is low, it easily penetrates into the concrete pores which promote the adhesion between the membrane and the concrete surface. In addition to that the primer also acts as a binder for the dust which gets accumulated on the concrete surface even after cleaning. 3 ALIGNMENT Start the installation of all membrane plies from the low point, so that the flow of water is over or parallel to the plies, but never against the laps. Begin membrane application by unrolling the roll of Dr. Fixit Samshield XL membrane and aligning the side lap

2- PART EPOXY ROLLER AND SELF-SMOOTHENING TOPPING.Sikafloor®-264 HC is a two part, coloured epoxy resin.Sikafloor®-264 HC may only be used by experienced professionals. Sikafloor®-264 HC may only be used by experienced professionals. Sikafloor®-264 HC is used as: Self-smoothening topping & Roller coat for concrete and cement screeds with normal up to medium heavy wear e.g. Production area, storage and assembly halls, maintenance workshops, garages and loading ramps. ▪ Seal coat for broadcast systems, such as multi-storey and underground car parks, maintenance hangars and for wet process areas, e.g. beverage and food industry

RITESEAL  (Cementitious Waterproofing System) is a cementitious based single component, highly polymer modified, flexible waterproof coating for all kind of cementitious surfaces. It has good water resistance properties  against water under hydrostatic pressure (up to 2 bar). It is to be mixed with water and applied by paint brush. This product can be used on walls and floors in wet areas such as bathrooms, kitchens, swimming pools, water  fountains etc.

MID RANGE WATER REDUCING & SLUMP RETAINING ADMIXTURE Areas of Application :- High Early Strength Concrete Upto M 45 Grade Pre Stressed Concrete MCON SRP 100 Precast Concrete Features :- High water reduction Reduces finishing labor costs due to optimized set times Faster turnover of forms due to accelerated early strength development

High strength self-smoothing epoxy underlay Uses Provides an economical method of levelling fl oors prior to laying epoxy screed, toppings or coatings such as Nitofl or FC140, Nitofl or FC150 and Nitofl or SL2000 and all other resin topping of Fosroc. Advantages  Cost eff ective  High strength  Quick and easy to lay  Seamless  Durable Description Nitofl or EU5 consists of special resins and graded aggregates formulated to withstand chemical attack and impact shock. The product is supplied as a 3 component system comprising resin base, resin hardener and fi llers. When correctly laid Nitofl or EU5 will provide a surface ready to receive applications of other Fosroc fl ooring systems. Standards compliance Nitofl or EU5 complies to IS 4631:2001. Technical Support Fosroc off ers a comprehensive range of high performance, high quality fl ooring, jointing and repair products for both new and existing fl oor surfaces. In addition, the company off ers a technical support package to specifi ers, end-users and contractors, as well as on-site technical assistance in locations all over the world. Design Criteria Nitofl or EU5 is designed for application upto 5mm thickness. Greater thicknesses can be achieved by the use of other products in the Nitofl or EU range - consult the local Fosroc offi ce for more details. Substrates should be surface dry and not suff er, or be likely to suff er, from rising dampness. If necessary, suitable damp-proof membranes should be installed to prevent this. Substrates should not have a moisture content greater than 5% at any time during the installation. 

Cebex 200 a plasticising and hydrogen free expansion grout admixture is supplied as a powder admixture. Cebex 200 allows the use of a reduced water / cement ratio with consequent increased strengths and durability. The expansive medium counteracts the natural settlement and plastic shrinkage of the grout and aids stability and cohesion.

Nitoproof Damp Protect is a High performance two component elastomeric cementitious damp-proof coating, suitable for application on RCC Roof/Wall, brick wall and plastered surface both positive & negative side. Areas of Application Masonry surface,concrete, plaster surface  and  brick      walls subjected to damage from moisture / effl  orescence.  Toilets and wet areas. Balconies, chajjas and utilities. Advantages Suitable for treatment of damp patches from negative side Excellent crack bridging ability. Excellent adhesion to concrete, masonry and plastered    surface. Long working life. Easy application by brush, roller, trowel or spray. Bonds to green or damp surface. Eff ective barrier to sulphates, chlorides & carbonation. Provides long lasting protection against effl  orescence. Description Nitoproof Damp Protect  is a two component acrylic polymer modifi ed cementitious coating which consists of  powder and liquid acrylic emulsion. It requires only  mixing  at site to produce an easily brushable coating.   Nitoproof Damp Protect can simply be applied by stiff  brush or roller  to obtain the desired thickness. Technical Support Fosroc off ers technical support service to specifi ers, endusers and contractors, as well as on-site technical assistance in locations all over the country. Nitoproof Damp Protect Properties Pot life Mixed density Colour Application temp. Adhesion to concrete Toxicity Intermediate coating time Curing time after 2nd coat Elongation at break,                   (ASTM D412) Crack Bridging                                             (ASTM C1305) Rapid chloride permeability resistance ASTMC1202 60 min @ 27oC 1.7 g/cc (brushable consistency) Off  White 10  -  35oC > 0.8 N/mm2 Non-toxic 4-6 Hrs 4-5 days 100 % No cracking up to 1.2 mm very low Application Instructions Surface Preparation All surfaces which are to receive the coating must be free from oil, laitance, grease, wax, dirt or any other form of foreign matter which might aff ect adhesion. Spalled surfaces or those containing large blow holes, cracks and other such defects should be repaired using Renderoc concrete repair mortars. For further advice on suitable repair mortars, contact the local Fosroc Offi  ce. Mixing/Usage Nitoproof Damp Protect  is mixed as per the proportion given  in the table  below and mixed with a slow speed drilling Machine   The powder component is added Gradually to the liquid to avoid lump formation and mix for 2-4 minutes. Mixing ratio Nitoproof Damp Protect           Components      15kg pack   5kg pack  Nitoproof Damp Protect powder  10kg           Nitoproof Damp Protect liquid     5kg           Application 3.33kg 1.67kg For   best   results,  surfaces   should  be   damp  or  in  SSD  condition . In order to obtain  the protective  properties of Nitoproof Damp Protect, it is important that the correct rates of application are observed. Use a short stiff  brush preferably 120 - 150mm width and apply the mixed material like paint. The application of Nitoproof Damp Protect should not be done if  the  temperature of  the  substrate  is  below 100C. When 

Waterproofing Chemicals Mumbai.
Dr Fixit Dealer.
Terrace Waterproofing Material Supplier.

In Dr Fixit there are varoius products available for waterproofing, seaants, exterior waterproof paints, membranes etc

SBS MODIFIED SELF ADHESIVE WATERPROOFING  MEMBRANE .Dr. Fixit Samshield P SBS modified self adhesive waterproofing membrane consists of a self adhesive polymer modified bitumen layer coated on to a tough high density polyethylene film and protected on the other side by a silicone release film. Typical Applications Dr. Fixit Samshield P membranes are generally used a waterproofing or damp proofing membranes intended for concrete protection. It may be used for horizontal and vertical application and as a damp proof course for tanking below ground structures, subways and retaining walls.

Buy Dr Fixit Samshield XL 1500 – high performance elastomeric waterproofing coating for walls & roofs. Ideal for terrace, balcony & external surfaces.
Dr. Fixit Samshield is a self-adhesive waterproofing membrane based on a tropical grade of polymer

GEOTEXTILE SURFACED SBS MODIFIED BITUMEN SELF ADHESIVE WATERPROOFING AND PROTECTION MEMBRANE.Dr. Fixit Samshield PS is a SBS modified bituminous, self adhesive sheet membrane laminated onto a tough polyester fleece to provide a

Dr. Fixit waterproof wall putty is a white cement-based wall putty that providessuperior leveling to the wall and resists water penetration, keeping freshlypainted walls looking bright for long. Dr. Fixit Waterproof Wall Putty Cement is a premium white cement–based wall putty designed to provide a smooth, durable, and water-resistant finish to both interior and exterior walls. It 

Concure LP90(M) concrete curing compound is polymer based continuous film forming curing compound and is supplied as aluminised polymeric resin solution drying to a silver film on application.

Concrete remover, cleaning and etching agentUsesFor the removal of mortar and plaster runs, droppings andstains from brickwork and concrete surfaces. Also for removalof hardened concrete from tools, machinery and equipment, orrust and mill scale from steelwork.Suitable for etching of concrete fl oors and surfaces prior toapplication surface coatings.AdvantagesRapid actionSafe with metals (except zinc and galvanised steel), wood,glass, plastic and rubber. No corrosive action. Penetrates oiland grease.DescriptionReebaklens is a combination of acid based material, corrosioninhibitors and dispersing agents and is supplied as a clearyellow solution.Technical SupportFosroc provides a technical advisory service to specifi ers, endusersand contractors as well as on-site technical assistancein locations all over the country.PropertiesSpecifi c gravity : Typically 1.08 at 250CApplication instructionsCleaning brickworkA small trial area should be cleaned fi rst to determine themost suitable Reebaklens cleaning agent dilution. Pre-wetthe brickwork, then using a sponge, rub the aff ected areaswith a solution of Reebaklens cleaning agent and water.Strength of the solution required will vary but should bebetween 1:1 and 1:4 (by volume of Reebaklens cleaningagent to water). When the action has fi nished, wash downthoroughly with clean water.Cleaning large items of equipmentE.g. Readymix trucks, concrete mixers, barrows, etc.Reebaklens cleaning agent should be liberally applied tothe deposits by a soft broom and allowed to soak overnightif possible. If the surfaces of the deposit can be cracked bymechanical means this will speed up the operation. In severecases more than one application may be necessary. Oncompletion, dissolved deposits and loose material should bewire brushed and washed away with clean water.

UsesIntegral sealing for construction joints in concrete cast in-situwhere conventional waterstops are impractical to use becauseof limited access.Convenient and problem solving in situations where a conventionalwaterstop would require complex shutteringTypical uses include secant piled and diaphragm walled basements,pile caps and casting against old concrete. SupercastSW20 can provide simple solutions to detailing pipe entries,construction joints in the vertical plane and to kicker joints.Can be linked to Supercast PVC*† waterstops to give an effectivecombination of waterstops which maintain networkcontinuity.Advantages Easy to install by bonding, nailing or casting intojoint faces Factory made connectors enable full integration ofSupercast SW20 and Supercast PVC networks Solves detailing problems in conjunction withSupercast PVC range Swelling properties unaff ected by long term wet/drycycling Tolerant of salts present in concrete and ground water Sustains eff ective seal in wet conditionsStandards complianceSuitable for use in contact with potable water - Water ByelawsScheme Approved product: Listing No. 9312507.DescriptionThe Supercast SW20 is a swellable waterstop which can beinstalled and positively linked into conventional SupercastPVC waterstop networksThis allows the use of Supercast PVC for expansion joints andSupercast SW20 for construction joints all the time maintainingan integrated network.The Supercast SW20 is made from high performance syntheticelastomer strips. The swelling action is the result of contactbetween water and hydrophilic groups which are part of theSupercast SW20 ‘Basic Polymer’ molecular structure.

CEMENTITIOUS NON SHRINK CRACK FILLER Areas of Application :Horizontal & Vertical Cracks External Crack Repairs Internal Crack Repairs MCON CRACK FILLER (Grey) Hair Line Crack Repairs Features :Allows breathing, thus preventing peeling and scaling Prepacked, only addition of precise quantity of water is required Dense & cohesive mortar will not allow water penetration

• Protects Nail Polish: Helps prevent chipping, cracking, and fading for long-lasting wear.
• Adds Shine or Matte Finish: Available in glossy or matte finishes for a polished look.
• Quick Drying: Many formulas dry quickly to speed up the manicure process.
• Strengthens Nails: Some top coats include strengthening ingredients to protect natural nails.

 

SPLASH is a clear single component, water based free flowing liquid developed specially for waterproofing of very difficult areas, wherein other waterproofing systems cannot be implemented. SPLASH is a ready to use material available in white turbid color, which penetrates in to the pores. It dries to a clear and tough film which gives high quality waterproofing. 

We are undertaking Cementitious based Injection grouting, Epoxy based Injection Grouting, PU foam injection grouting works

 ZYCOSIL is an organosilane capable of modifying various materials, transforming them into hydrophobic surfaces. Thus, it can be used as a waterproofing for building materials. It is stable against water, light and heat, providing durable waterproofing solutions.

High-strength epoxy adhesive: Masterbond SG 800 is a two-part epoxy adhesive known for its strong bonding capabilities.

Broad substrate compatibility: It can bond a wide range of materials, including metals, ceramics, plastics, and composites.

Harsh environment resistance: It's designed to withstand exposure to chemicals, solvents, and extreme temperatures.

Versatile applications: Commonly used in aerospace, electronics, and other demanding industrial applications

HIGH BUILD ELASTOMERIC BITUMINOUS POLYURETHANE BASED WATERPROOFING MEMBRANE DESCRIPTION TECHOTHANE PU is high performance PU based cold applied elastomeric coating. The high elasticity, excellent bond and low water permeability of Techothane PU make it ideal for a wide range of water/vapour proofing applications. FEATURES  Non-toxic 

TECHFOAM PU-103 is a two-component, phthalate free, hydrophobic, polyurethane injection grout to be used as water stop. Techfoam PU-103 is solvent free and MDI-based water reactive polyurethane injection foam. It reacts ONLY with water forming a semi-rigid hydrophobic seal. It expands over 30 times of its original volume when brought in contact with water. 

INTEGRAL WATERPROOFING POWDER FOR CONCRETE AND PLASTER Areas of Application :- Brick Bat Coba Application Roof Slabs & Screeds Sumps & Drains MCON LWP Bathrooms & Balconies Features :- Easy to use – Simple application familiar to site operations Workability – Improves workability Reduce mortar dropping,when used in plaster 

Choksey Hydrofoam, specifically Purinject 1C Hydrofoam, is a low-viscosity, solvent-free polyurethane injection resin used for sealing non-structural cracks, water ingress, and leaks, particularly in concrete structures. TECHFOAM PU-103 is a two-component, phthalate free, hydrophobic, polyurethane injection grout to be used as water stop. Techfoam PU-103 is solvent free and MDI-based water reactive polyurethane injection foam. It reacts ONLY with water forming a semi-rigid hydrophobic seal. It expands over 30 times of its original volume when brought in contact with water. RECOMMENDED USES  Sealing of water bearing cracks in concrete and masonry by pressurized single component injection equipment.  Basements, underground / overhead water tanks, swimming pools  Wet rooms and other superstructures  Tunnels and water reservoirs  Metros SUITABLE SUBSTRATE  Mineral substrates, e.g. concrete, cement, brick  Sealing of water bearing cracks  Metal and certain plastics ADVANTAGES  Techfoam PU-103 forms after the reaction with water a semi-rigid seal in the crack or joint.  Fast reacting semi rigid PU foam, used as a water stop for the sealing of leakages or to stop active water leaks with a high flow and/or high hydrostatic pressure  Penetrates deep in fine cracks; because of its low viscosity.  Free expansion upto 20-30 times by volume.  Depending on the amount and the velocity of the water leakage, the reaction time can be changed by adding more or less Part-2.  Excellent adhesion to mineral construction materials (such as concrete, cement, brick), metal and certain plastics)  Techfoam PU-103 foam is chemically resistant against water, weak acids and alkali, mineral oils, fungus and bacteria, ground water, sea water etc. 

A single-pack, ready-to-use, non-shrink, cementitious repair mortar for concrete and plastered surfaces. Ideal for repairing damaged reinforced concrete elements.

MYMIX SBR 330 is a Styrene Butadiene Rubber Latex for improving adhesion strength of all types of cement based mortars with water and vapour resistant bonding properties. Best before 12 months from the date of manufacturing, in unopened condition and stored in dry area. Avoid direct sun light.

Cleaners & Stain Removers of Algae, organic stains, cement stains, greasy , oil and dirty floors, rust stains on stones, paint striper.
Guard Wash® Express is a concentrated product with powerful active materials enabling instant and deep cleaning of dirt invading building materials (dirt associated with damp, atmospheric pollution, traces of leaves, etc.). The self-cleaning, quick and powerful action of Guard Wash® Express cleans contaminated surfaces. The original appearance of materials is restored in less than an hour with no deterioration to their colour or their mechanical properties. Guard Wash® Express is also the ideal product to remove grey discolouration from wood. USE Guard Wash® Express is an ideal universal product to treat external walls, facades, weather boarding, roofs, balconies, fountains, pools, monuments, fences, terraces, garden paving, paving, tennis courts, etc. It can be used on all materials like concrete, fibre cement, natural or reconstituted stone, terracotta, tiling, PVC, wood, etc. Particularly recommended for renders (even painted) and all types of coatings. ADVANTAGES AND CHARACTERISTICS • Instant and ultra-fast action in 1 application. • Deep cleaning without mandatory rinsing. • Can be used on a wide range of materials. • Does not damage mineral materials, even glass. • Low odour and long-term storage. • Ultra concentrated formula = effective and fast. • Ready to use: quick and easy to use.