Venus Enterprises

DR. Fixit Gap Seal Tape is a self-adhesive, aluminum or high density polyethylene surfaced bitumen & SBS rubber backed sealing strip. It is a quick, efficient and cost effective method of flashing, sealing and repair that produces a lasting protection in all climates.

Superior sealing system for pipe and utility penetration. Description Nitoband TPE Collar is a special prefabricated gasket for sealing of pipe and utility penetration made of non-woven fabric on both sides with Thermoplastic elastomeric (TPE) membrane in the center which is highly fl exible. Nitoband TPE Collar is available in diff erent diameters to facilitate detailing of diff erent penetrations. Nitoband TPE Collar is highly resistant on hydrostatic pressure and vapor permeable, tear proof and chemical resistant. Very good behaviour on temperature diff erences. Applications ■ For permanent sealing of pipe and utility penetrations through walls and fl oors in common with mostly all liquid applied waterproofi ng membranes ■ Can be used underneath ceramic tiles and natural stones in outdoor or indoor construction like bathrooms, showers, balconies, terraces etc. Speciation Clause Where required, all pipe and utility penetrations are to be waterproofed using Nitoband TPE Collar flexible permanent sealing prefabricated gasket system with non-woven fabric on both sides with Thermoplastic elastomeric (TPE) membrane in the center. To be used with Nitoband TPE and liquid applied waterproofing membrane. The Nitoband TPE and Nitoband TPE Collar System meets the performance criteria and are approved products Installation Step 1: Pipes penetration needs to be cleaned with suitable means before application of liquid applied waterproofing membrane. 

Liquid-applied Polyurethane Waterproofing Membrane  Solvent-free  Product Description Advantages   MARISEAL 300 is a liquid-applied, solvent-free, hard-elastic, cold applied and cold curing, two component polyurethane membrane used for long-lasting waterproofing and protection.  Cures by reaction (cross linking) of the two components.   Tested for safe use in potable (drinking) water reservoirs by NSF  When applied forms seamless membrane without joints or leak possibilities  Resistant to cold water, warm water and frost  Maintains its mechanical properties over a temperature span of   -30oC to +90oC (not suitable for wet load over +60oC)  Remains elastic even at low (frost) temperature  Odor free  Full surface adherence  The waterproofed surface can be walked on  Main Uses Consumption   Drinking Water Tanks and Reservoirs (fully      Reinforced)   Drinking Water Supply Channels (fully      Reinforced)    Drinking Water Pipes  Swimming Pools (under tiles)    Packaging  MARISEAL 300 A+B is supplied in 6+1 kg and 15+2,5 kg metal pails. Pails should be stored in dry and cool rooms for up to 12 months. Protect the material against moisture and direct sunlight. Storage temperature: 5o-35oC.  Products should remain in their original, unopened containers, bearing the manufacturers name, product designation, batch number and application precaution labels.   2,0- 2,5 kg/m2 in more than two layers fully reinforced.  This coverage is based on practical application by roller onto a smooth surface in optimum conditions. Factors like surface porosity, temperature, humidity, application method and finish required can alter consumption.     Colours  MARISEAL 300 is supplied in off-white, blue and grey. Other RAL colours on demand. Due to the sensitivity of aromatic polyurethane to UV rays, the applied coating might yellow and fade on the surface. This change in appearance does not modify its mechanical properties or leak tightness.     Certifications   The MARISEAL 300 is tested according to the BS 6920:2000 by the NSF Laboratory in the United Kingdom, for use on surfaces in direct contact with potable (drinking) water, and potable (drinking) water storage tanks.  MARISEAL 300 is certified according to the Singapore Standard SS 375:2001 “Suitability of non-metallic products for use in contact with water intended for human consumption with regard to their effect on the quality of the water” and was found conforming.               Technical Data * PROPERTY  RESULTS Composition TEST METHOD Mixing Ratio  Polyurethane Resin + Hardener  A+B = 6:1 by weight  Resistance to Water Pressure No Leak (1m water column, 24h) Elongation at Break DIN EN 1928 >60% (without reinforcement) Adhesion to concrete ASTM D 412 >2,0 N/mm 2  Pot life  EN 1542 30min@20oC Hardness (Shore A Scale) 70 + 5 Inhouse Lab ASTM D 2240 Solids Content 100% UV accelerated ageing, in the presence of moisture CALCULATED Passed - No significant changes Hydrolysis (5% KOH, 7days cycle) EOTA TR-010 No significant elastomeric change Service Temperature  Inhouse Lab -30oC to +90oC (not suitable for wet load over +60oC) Tack Free Time 6-8 hours  Inhouse Lab Light Pedestrian Traffic Time Final Curing time (ponding test) 24 hours 7 days  Conditions: 20oC, 50% RH Chemical Properties Good resistance against acidic and alkali solutions (5%), detergents, seawater and oils. Not suitable for contact with industrial wastes.   

Zydex Wall Tex is an acrylic-based, textured scratch finish paint that provides a durable, water-resistant, and visually interesting finish for walls, suitable for both interior and exterior applications. 

HDPE (High-Density Polyethylene) Self-Adhesive Membrane is a type of waterproofing material commonly used in construction projects. Here are some details about this product: 

1. Material: HDPE Self-Adhesive Membrane is made from high-density polyethylene, a thermoplastic polymer that is known for its durability, strength, and resistance to environmental factors such as UV rays and chemicals.
2. Waterproofing: The primary function of HDPE Self-Adhesive Membrane is to provide waterproofing to concrete structures such as roofs, foundations, and basements. Its self-adhesive property allows for easy and quick installation, making it an ideal option for large-scale projects.
3. Thickness: HDPE Self-Adhesive Membrane comes in different thicknesses, ranging from 1.0mm to 3.0mm. The thickness required for a particular project depends on factors such as the structure's size, location, and intended use.
4. Durability: HDPE Self-Adhesive Membrane is highly durable and can withstand harsh environmental conditions, including extreme temperatures and heavy rainfall.
5. Easy to Install: The self-adhesive property of this membrane makes it easy to install without the need for additional adhesive or bonding agents. It can also be easily cut to size to fit specific structures.
6. Cost-effective: HDPE Self-Adhesive Membrane is a cost-effective waterproofing solution compared to traditional methods such as bituminous membranes or liquid waterproofing systems.

 Overall, HDPE Self-Adhesive Membrane is a popular choice for waterproofing in the construction industry due to its durability, ease of installation, and cost-effectiveness.Applications:HDPE Self-Adhesive Membrane is a versatile waterproofing material that has a wide range of applications in the construction industry. Some common applications include: 

1. Roof Waterproofing: HDPE Self-Adhesive Membrane is commonly used to waterproof flat or sloping roofs, protecting the underlying structure from water damage.
2. Foundation Waterproofing: It is also used to waterproof foundations and basements, preventing water from penetrating the walls and causing structural damage.
3. Bridge Decks: HDPE Self-Adhesive Membrane is used to waterproof bridge decks, ensuring the longevity of the bridge by preventing water and other contaminants from penetrating the structure.
4. Tunnels: It is used to waterproof tunnels, protecting the structure from water seepage and prolonging its lifespan.
5. Landfill Liners: HDPE Self-Adhesive Membrane is used to line landfills, preventing the leakage of waste materials into the environment and protecting groundwater.

High build fi bre Reinforced Acrylic Elastomeric Waterproofi ng coating for Roofi ng Uses Brushbond Roofguard is high build fi bre reinforced seamless waterproofi ng coating suitable for waterproofi ng of old & new roofs. It is a polymer based product applied in multiple coats. The product can be applied directly on existing concrete, brickbat coba, and screed concrete even without removal provided the substrates are sound enough for application of the coating avoiding the risk of damage to the old roof associated while removing of the existing overlays. The product provides a seamless, tough durable water resistant coating which can withstand light pedestrian traffi c and also has excellent weather resistance for exterior applications. Advantages  High Build system provides higher dry fi lm thickness of more than 0.8mm.  The product can applied directly on existing sound concrete, brickbat coba, screed concrete even without removal No protection screed required eliminating the additional weight due to protection layer Excellent barrier to carbon dioxide, chloride and sulphate ions. Allows water vapour to escape from the structure. High resistance to the eff ect of long-term weathering, Durable in all climate conditions including UV attack. Excellent bond to concrete and masonry. Good crack accommodation capacity. Minimum surface preparation needed and low labour. Standards compliance Tested to ASTM D4541, ASTM D412, ASTM G154, ASTM E96

PRODUCT DESCRIPTION VANDEX BB 75 is a cementitious, ready-mixed surface waterproofer. AREAS OF APPLICATION − Substrates: concrete and masonry − active or passive waterproofing and protection against water and moisture − foundations, slabs, retaining walls, etc. − drinking water structures PROPERTIES Owing to its composition of cement, quartz with graded grain-size distribution and  selected additives, VANDEX BB 75 is waterproof. It can be employed against active and passive water pressures. The initial and final bonding capability of VANDEX BB 75 is excellent, making it suitable to be applied to horizontal as well as vertical surfaces. It is durable, resistant to frost and heat after setting, but all the same permeable to vapour. VANDEX BB 75 is tested for use in contact with drinking water. SURFACE PREPARATION The substrate to be treated must be sound and even, openpored, roughened and its surface free from voids, large cracks or ridges. Any adhesion reducing substances like bitumen, oil, grease, remains of paint or laitance must be removed by suitable means.  Water leaks must be stopped e.g. with VANDEX PLUG.  Thoroughly moisten the substrate it must be damp but not wet at the time of application. Any surface water on horizontal surfaces must be removed. Brick- and blockwork substrates Any remaining plaster, render or other substances that could inhibit bonding must be removed back to the substrate. Gypsum, remains of wood or other foreign material must be removed by appropriate means. Loose pointing must be routed out and the substrate cleaned thoroughly. MIXING Mix 25 kg of VANDEX with 4.5–6 litres of tap water in a clean container for at least 3 minutes to a lump-free, homogeneous consistency. Use a mechanical mixer. 

Water resistant polymer additive / bonding agent, to provide improved adhesion to concrete Uses For improving and bonding concrete repair mortars, cementitious floor toppings and screeds, waterproof renders and cementitious slurries. Cementitious mortars are alkaline in nature and will protect embedded steel reinforcement. Mortars produced with Nitobond SBR may be used for horizontal, vertical and overhead repair work. Advantages  Excellent bond to concrete, masonry, stonework, plaster and blockwork  Improved tensile and flexural properties allow thinner applications  Single component liquid can be easily gauged as required  Improves cohesion and workability  Improves mortars to provide waterproof repairs, renders and toppings which are highly resistant to freeze/thaw cycling Description Nitobond SBR is a modified styrene butadiene rubber emulsion which is supplied as a ready to use white liquid. It is designed to improve the qualities of site-batched cementitious mortars and slurries. Being resistant to hydrolysis, it is ideal for internal and external applications in conjunction with cement. Design Criteria The application parameters for mortars modified by the use of Nitobond SBR will differ depending on the actual mix design used. Generally, however, Nitobond SBR mortars can be applied in sections up to 40mm thickness in horizontal locations and up to 15mm in vertical locations. The thickness achievable in overhead locations without the use of formwork is largely dependent on the profile of the substrate. Vertical and overhead sections greater than those stated above may be built up in layers but may sometimes be possible in a single application dependent on the actual size and configuration of the repair area, and the volume of any exposed reinforcing steel. Nitobond SBR mortars should not be applied at less than 6mm thickness. Thicknesses up to 40mm in a s

Matt Emulsion is a premium interior paint with a rich matt finish. It’s inherent deep matt effect and carefully selected pigments provide unsurpassed color depth and brilliancy even in the most difficult lighting conditions. Matt Emulsion’s ability to hide surface defects leads to an even and consistent finish even at sharp angles. The paint is extremely resistant to burnishing and mechanical abrasion making it suitable for even the most demanding high traffic interior spaces. Being highly breathable, it is extremely resistant to peel-off and blistering. Designed for excellent dirt release, it is easily washable and highly scrub resistant. Available in a white and pastel tones. 

Bituminous waterproofing membrane wet appliedDESCRIPTIONSikaShield® W159 ED 1,5 mm is an adhesive bituminouswaterproofing membrane wet applied to the concretesurface by the adhesive mortar SikaShield® W1IN. It has a thickness of 1.5 mm and is flexible at -15°C. It is reinforced with a cross-laminated PE film,which gives high mechanical properties to the membrane.The top surface and the underside have a removableliner over the adhesive compound for aneasy application.USESThe Product is used as a waterproofing membrane for:▪ Basements and other below ground structures▪ Vertical reinforced concrete walls▪ Single and strip foundationsThe Product is used as a:▪ Single layer under heavy protection▪ Base sheet in multi-layer systemsPlease note:The Product is not suitable for roofs permanently exposedto UV radiation.▪CHARACTERISTICS / ADVANTAGESNo-torch application allows for safe installation inconfined spaces▪▪ Fully bonded system ensures reliable waterproofing▪ Watertight against lateral water migration▪ Can be applied on wet concrete▪ Fast and easy installation▪ Flame-free application▪ Requires minimal surface preparation▪ High impact resistanceBituminous waterproofing membrane wet appliedDESCRIPTIONSikaShield® W159 ED 1,5 mm is an adhesive bituminouswaterproofing membrane wet applied to the concretesurface by the adhesive mortar SikaShield® W1IN. It has a thickness of 1.5 mm and is flexible at -15°C. It is reinforced with a cross-laminated PE film,which gives high mechanical properties to the membrane.The top surface and the underside have a removableliner over the adhesive compound for aneasy application.USESThe Product is used as a waterproofing membrane for:▪ Basements and other below ground structures▪ Vertical reinforced concrete walls▪ Single and strip foundationsThe Product is used as a:▪ Single layer under heavy protection▪ Base sheet in multi-layer systemsPlease note:The Product is not suitable for roofs permanently exposedto UV radiation.▪CHARACTERISTICS / ADVANTAGESNo-torch application allows for safe installation inconfined spaces▪▪ Fully bonded system ensures reliable waterproofing▪ Watertight against lateral water migration▪ Can be applied on wet concrete▪ Fast and easy installation▪ Flame-free application▪ Requires minimal surface preparation▪ High impact resistance

General purpose, high flow, Class A shrinkage compensated grout - (gaps 10mm to 100mm thickness) Uses Conbextra GP is used for general purpose grouting where it is essential to elim

 • Very high compressive and flexural strength at very short time. • Longer pot life ensuring negligible wastage. • Non-shrink grout with controlled positive expansion ensures proper load transfer and durability of structure. • High fluid consistency and bleed resistance. • Quickly and easily placed by pouring or pumping. • Resists chemical attack, oils, petroleum products, solvents, and mild caustic alkalis. • No added chloride or gypsum. • Excellent for dynamic and static loading conditions. • Free of chlorides and additives, that may lead to corrosion. • High drill resistance property. • Self-compacting. • Product variants available in both Flow-able and Normal Trowel-able consistency. “

weberset classic is a high polymer modified thin-set tile adhesive, spe application. This is also suitable for tile-on-tile application for fixing vitrified tiles on pre-existing ceramic tile floors.

MCON Bond APL is an acrylic polymer-based bonding agent formulated from selected synthetic copolymers. It is designed to enhance adhesion between old and new concrete surfaces, providing a strong bonding coat that protects and repairs RCC and steel structures. This product is ideal for applications requiring improved flexural, tensile, and thin-section fragility of cementitious systems. Additionally, it is non-toxic, making it suitable for structures storing potable water.

 Universal polyester resin for all types of materials.  Valid for all types of concrete, non-cracked, and all concrete applications. Valid for hollow and solid masonry.  Stone colored version.  Valid studs from M8 to M24.  Use for medium loads.  Valid for dry, wet and flooded holes.  Use for static or quasi-static loads.  Versions in zinc plated and stainless steel A2 and A4.  Service temperature range: from -40ºC to +80ºC (long term maximum temperature +50ºC).

It’s a single-component thixotropic thin-bed fixing and jointing block grip adhesive. It contains anaggregate ratio of graded inert sand with cement and polymers for applications as a bond-grippingmaterial in civil construction works. It is recommended for fixing and jointing AAC blocks, ALC blocks,cement mortar blocks, cellular concrete blocks, fly ash bricks and composite cement blocks.

Techfloor-Mortar is a three pack, solvent free epoxy resin system. In hardened, condition Techfloor Mortar gives excellent hardness, abrasion resistance & chemical resistance. 

Superior sealing system for critical joint areas in place of traditional bondbreaking sealants and tapes Uses The Nitoband System is used in conjunction with Nitoproof water based membranes as an alternative to traditional bond breaking methods for sealing critical movement zones. It is suitable for internal, external underground and fully immersed applications. Advantages  Can be used with Nitoproof water based single or 2 part liquid membrane systems  Time efficient and simplified installation – no time wasted waiting for joint sealants to sufficiently skin and cure  High elongation and movement capabilities - able to withstand movement in both longitudinal and lateral directions  High strength rubber composition with superior water, chemical and tear resistance  Waterproof in its own right, which offers double protection when combined with a Nitoproof water based liquid membrane over-laid  System comes with pre-fabricated corners, pipe penetration detailing squares for superior sealing in the most critical of areas Description The Nitoband System is a combination of acrylonitrile butadiene rubber (NBR) tape and detailing accessories designed and developed as a superior bond breaking alternative to traditional methods of sealing critical movement zones when used in conjunction with Nitoproof water based liquid applied waterproofing membranes. Standards Compliance The Nitoband System meets the requirements of AS 3740 and is suitable for use with Class I, Class II and Class III membrane systems as per AS4858 and AS4654.

MYMIX Grout Admixture 990 is used in place of water to improve the quality of cement grouts. It is ideal for interior and exterior tile grout application and enhances flexibility durability to have better performance. Advantages: Reduces water absorption.

BM Coat – 6015  / BM PRIME SBD41 is a Rubber Modified Bitumen Emulsion Coating. After the field has been emulsified, the water evaporates and the emulsifier with traces of bitumen in the surface dries to form a tough, seamless, flexible water proof coating. It conforms to the requirement of ASTM Standard.

Basement waterproofi ng protection to grades 1,2 and 3 as defi ned in BS 8102: 2009 & IS 16471 : 2017  To provide a vapour and waterproof ve adhesive and remaining in place if settlement of t Facilitates fl exible construction programming Full range of Fosroc hydrophilic and PVC waterstops available to provide complete solution to waterproofi ng of the structure

We are specialized in strenthening of RCC membres like Beams, Columns, Slab, foundations with polymer Mortaring/ Epoxy Mortaring / Jacketing / carbon Fiber wrapping system . We are also specialised in doing waterproofing with different syestems without breaking existing system or with breaking and re doing in new one, We also do external watreproofing painting  and internal  paintings.