Venus Enterprises

Atactic Poly Propylene (APP) modified bituminous membrane with PE foil (Formerly Sika® WP Shield-103) DESCRIPTION SikaShield® P22 PE IN 3 mm is an APP modified bituminous waterproofing membrane with a thickness of 3 mm. It is reinforced with a hybrid composite reinforcement fabric and is flexible at 2 °C. The top surface is coated with polyethylene foil, which ensures the bond of the overlying layer. The underside of the product has a burn-off film for easy torch-application. USES The product is used as a waterproofing membrane for: Balconies and terraces under a heavy protection layer such as tiles or gravel. ▪ Flat and sloping roofs under protective layers or ballast ▪ ▪ Car park decks ▪ Bridge decks under asphalt wearing layer ▪ Underpass and subways ▪ Basements and other below ground structures Horizontal reinforced concrete slabs, decks, podiums and protrusions ▪ ▪ Vertical reinforced concrete walls The product is used as a: ▪ Base sheet in multi-layer systems Please note: The product is not suitable for roofs permanently exposed to UV radiation. Protect membrane with a suitable protection layer. ▪ CHARACTERISTICS / ADVANTAGES ▪ Fully bonded ▪ Long term flexibility ▪ Excellent water tightness ▪ Good mechanical properties (tensile, tear) ▪ Can be handled in warmer temperatures easily ▪ Low water absorption ▪ Easy to install by torching method Capable of withstanding thermal and structural stresses ▪ Good durability and performance under long term ageing ▪ PRODUCT INFORMATION Chemical base Composition APP modified bitumen Reinforcing material Hybrid composite fabric Packaging Roll width 1.0 m Roll length 10.0 m (EN 1848-1) Shelf life 12 months from date of production

DESCRIPTION SikaShield® P24 MG IN 4 mm is an APP modified bituminous waterproofing membrane with a thickness of 4 mm. It is reinforced with a non-woven polyester fabric and is flexible at -2 °C. The top surface is coated with mineral granules, which allows the permanent exposure to UV radiation. The underside of the product has a burn-off film for easy torch-application. USES The product is used as a waterproofing membrane for: ▪ Balconies and terraces ▪ Flat or sloping roofs with up to 15 % gradient ▪ Bridge decks under asphalt wearing layer Horizontal reinforced concrete slabs, decks, podiums and protrusions ▪ The product is used as a: Exposed single-layer or as a top sheet in a multi-layer roofing systemCHARACTERISTICS / ADVANTAGES ▪ Decorative mineral granules ▪ Can be painted immediately after application ▪ Fully bonded ▪ Long term flexibility ▪ Excellent water tightness Very good mechanical properties (tensile, tear, shear) ▪ ▪ Can be handled in warmer temperatures easily ▪ Low water absorption ▪ Easy to install by torching method Capable of withstanding thermal and structural stresses ▪ Good durability and performance under long term ageing ▪ ▪ Tiles can be placed directly onto the membrane

Atactic Poly Propylene (APP) modified bituminous membrane with PE foil and flexible at -2 °C (Formerly Sika® WP Shield-104 P) DESCRIPTION SikaShield® P24 PE IN 4 mm is an APP modified bituminous waterproofing membrane with a thickness of 4 mm. It is reinforced with a non-woven polyester fabric and is flexible at -2 °C. The top surface is coated with polyethylene foil, which ensures the bond of the overlying layer. The underside of the product has a burn-off film for easy torch-application. USES The product is used as a waterproofing membrane for: Balconies and terraces under a heavy protection layer such as tiles or gravel. ▪ Flat and sloping roofs under protective layers or ballast ▪ ▪ Car park decks ▪ Bridge decks under asphalt wearing layer ▪ Underpass and subways ▪ Basements and other below ground structures Horizontal reinforced concrete slabs, decks, podiums and protrusions ▪ ▪ Vertical reinforced concrete walls The product is used as a: ▪ Base sheet and/or top sheet in multi-layer systems Please note: The product is not suitable for roofs permanently exposed to UV radiation. Protect membrane with a suitable protection layer. ▪ CHARACTERISTICS / ADVANTAGES ▪ Fully bonded ▪ Long term flexibility ▪ Excellent water tightness Very good mechanical properties (tensile, tear, shear) ▪ ▪ Can be handled in warmer temperatures easily ▪ Low water absorption ▪ Easy to install by torching method Capable of withstanding thermal and structural stresses ▪ Good durability and performance under long term ageing ▪ PRODUCT INFORMATION Chemical base Composition APP modified bitumen Reinforcing material Non-woven polyester fabric Packaging Roll width 1.0 m Roll length 10.0 m (EN 1848-1) Shelf life 12 months from date of production Storage conditions The product must be stored in original unopened and undamaged packaging in dry conditions and temperatures between +5 °C and +35 °C. Store in a vertical position. Do not stack pallets of the rolls on top of each other, or under pallets of any other materials during transport or storage. 

A mineral-finished APP (Atactic Polypropylene) membrane is a waterproofing material used on roofs and other surfaces. It's a type of modified bitumen membrane reinforced with a polyester or fiberglass mat and coated with APP-modified bitumen and mineral granules. The mineral granules provide UV resistance and an aesthetic finish

BM SELF  / SELF XL / P is a polymer modified self-adhesive, flexible, waterproofing and sealing membrane with high density polythene film on its upper side and detachable silicone film which can be found on the underside.

SikaShield® P24 MG IN 3 mm is an APP modified bituminous waterproofing membrane with a thickness of 3 mm. It is reinforced with a non-woven polyester fabric and is flexible at -2 °C. The top surface is coated with mineral granules, which allows the permanent exposure to UV radiation. The underside of the product has a burn-off film for easy torch-application. USES The product is used

BM Torch / Torch G / BM FELT membranes, manufactured with high quality bitumen and specialized polymers (APP-Atactic polypropylene) mixed together to obtain excellent heat and waterproofing properties. They have good UV resistance and are quite durable. The membrane ha

AQUAFLEX® AWP 350 is an advanced, one component, elastomeric waterproofing membrane which is thixotropic in nature and has UV resistance properties. It is ideal for use on horizontal surfaces. AQUAFLEX AWP 350 forms a tough, flexible 

Description Smartcare TPO Membrane is a combination of both polypropylene (plastic) and ethylene-propylene (rubber) which exhibits excellent versatile physical properties of plastic and rubber featured with pliable and weldable properties. Uses Smartc

Description SmartCare PVC Membrane is a synthetic flexible PVC membrane made of plasticized PVC manufactured by two colored co-extrusion method for waterproofing of tunnels and below ground structures. Uses SmartCare PVC Membrane can be applied

Waterproofing Chemicals Mumbai.
Dr Fixit Dealer. Fosroc Dealer, Sika Dealer, BASF Dealer, ACC Dealer, Ultratech Dealer, Asian Paints Dealer, Asian Smartcare Dealer, Berger Dealer, Mcon Rasayan Dealer, STP Dealer, Walplast Dealer, Ascolite Dealer, Magnigrout Dealer, Glass Fiber dealer, Non Woven Geotextile Dealer, KDM Dealer, GP2 dealer, Choksey Dealer, Stone and Impregnator dealer.
Terrace Waterproofing Material Supplier.
Fleece-backed fully bonded synthetic TPO waterproofing membrane Uses Provides a fully bonded waterproof membrane system for building and civil engineering structures and is particularly suited to above ground applications. „ Podiums and flat / sloping roof waterproofing „ Green / garden roofing Advantages „ Adhesion to common cementitious building materials „ High resistance to weathering and UV „ Resistance to root penetration „ Fast application „ Welded joints for maximum watertightness „ Excellent long term performance Standards Proofex OFB has been independently tested to comply with AS 4654.1-2012 as a Class III membrane - external/exposed. The test report 272-2 is available from the Fosroc web site. Description Proofex OFB is a TPO/FPA (Thermoplastic Polyolefin Flexible Polypropylene Alloy) membrane produced by extrusion of granules resulting from the incorporation of ethylene propylene rubber into a polypropylene matrix together with other additives as appropriate to the type of membrane. A synthetic polyester fleece is attached to the bottom part of the membrane, leaving a selvedge on both sides for welding. The membrane is manufactured in two different coloured layers, it is coloured with a grey layer on top and green layer on the underside. This helps to identify any damages that may occur during application.

TECH FLOOR SL-2 is a special blend of selected epoxy resins, curing agents and graded inert aggregates which when mixed, provides a 2 mm epoxy resin floor topping with unique laying properties. It provides a hardwearing attractive floor which is chemical resistant, impervious and extremely clean. FEATURES/ADVANTAGES  It provides dust free, seamless floor which is extremely easy to clean.  Good abrasion resistance withstands foot and light vehicular traffic.  Excellent in chemical resistance.  Available in a wide range of colours to provide a very attractive floor finish. TYPICAL APPLICATIONS  Mainly used on floor where high degree of cleanliness and hygiene are required.  Can be used for hospital clean rooms, electronic assembly areas, food and chemical plant, Slaughter houses and distilleries. TYPICAL CHARACTERISTICS Nature      Colour      Mixing ratio     Pot life at 30°C     Initial cure at 30°C     Total Curing time at 30°C.    ENGINEERING DATA SPECIFICATION COMPLIES   Compressive STRENGTH, KG/CM2  FLEXURAL STRENGTH, KG/CM2   Tensile STRENGTH, KG/CM2   Impact Resistance, KG/CM2   Abrasion Resistance, mm    : Three Component (Part I, Part II & Graded Filler) : Light grey, dark grey, light green, light blue. Etc. Colours  Can be provided as per the specifications if so required. : Part I (base : part 2(hardner) : part 3 (filler) : 3 : 1 : 7 : 1 hour : 18 hours (light foot traffic) : 6 days : BRITISH STANDARD SPECIFICATION, BS - 6319 : 500 : 350 : 180 : 5 TO 6 : 2 

Nafufill SBR SBR based Bonding Agent and Polymer Component for Repair Mortars, Cement Screeds, Water Proofing and Polymer Cement Concrete Areas of Application • The production of repair mortars, e.g. in the repair and filling of structural concrete in bridge building and civil engineering • Bonding slurry between hardened concrete and fresh topping of concrete or mortars • For bonding new cementitious materials to existing cementitious substrates on horizontal or vertical surfaces • Cold joints between old and new concrete can be made strong and non-permeable with bonding slurry consisting of Nafufill SBR and cement mortar • Improvement of the mechanical characteristics of ready-to-use coarse and fine repair mortars intended for the repair of concrete (such as Zentrifix AS & Nafuquick) • Second component for Dichtament DS waterproofing system • Bonding mortars for bonding of hard-burned bricks, asbestos cement, natural stones, tiles etc. • Repairs mortars for mending damaged spots in precast concrete industry, pipelines etc. Application Notes General Nafufill SBR is a high Sponification-resistant latex dispersion for improving adhesive strength of all types of commonly used mortars. It is suitable as an admixture for obtaining waterproof concrete and mortars. It is suitable for preparation of repair mortars. Instructions for Use The base must be clean and free from loose particles, dust, grease, oil or other remnats. All laitance should be removed by wire brushing. In some cases, the existing concrete must be chipped to a sound substrate. Where surfaces are contaminated with oil or grease, this should be removed by using a strong industrial detergent or organic degreaser. The base must comply with the srequirements laid down by competent authorities. Minimum tensile strength of substrate should be 1.5 N/ mm2. Application All repair systems need a bond coat to be applied on the prepared surface. The bond coat should be forcefully & evenly brushed into the substrates after the pre-moistened surfaces have dried. Repair Mortar: The repair mortar should be applied wet-on-wet after the bond coat while it is still fresh. The compositions of bond coat & repair mortar for different cases are given below. In general the dosage of Nafufill SBR varies as per the actual requirements. In general, for normal repair mortars, we recommend about 8 to 10% Nafufill SBR by weight of cement. For extreme condition the dosage of Nafufill SBR should be increased. Curing Nafufill SBR inhibits rapid drying-out of the fresh mortar. The mortar should all the same be suitably protected from rapid drying in order to ensure uniform development of strength. Please note that all generally applicable regulations and working principles must be observed when using Nafufill SBR for the production and application of cement mortars/plaster

Pre-applied fully bonded HDPE self-adhesive membrane with protective sand layer for belowground waterproofingDESCRIPTIONSikaProof®-312 HDPE SG IN is a unique HDPE basedself adhesive fully bonded sheet membrane comprisingof a virgin HDPE layer, coated with a high bondstrength adhesive, covered by a weatherproof protectivesand sprinkled layer, for below ground waterproofingof reinforced concrete structures. It is looselaid onto prepared substrates or formwork before fixingreinforcement and casting concrete. The adhesivelayer is activated when the concrete is poured on thesurface and forms a permanent bond with the freshconcrete which will prevent the ingress of wateraround the structure. Reinforcement can be directlylaid on top of the membrane and it does not requirescreed protection.USESSikaProof®-312 HDPE SG IN can be used for dampproofing,waterproofing and concrete protection forbasements, subway, tunnel and other below groundconcrete structures against ground water ingress. Suitablefor use on:▪ Reinforced concrete base slabsReinforced concrete walls with single and doublefacedformwork▪▪ Reinforced concrete footings and grade slab▪ Extension and reconstruction works▪ Prefabricated structuresCHARACTERISTICS / ADVANTAGESPre-applied: Fixed before placing reinforcement andcasting concrete▪▪ Strong adhesive bond with fresh concrete▪ High flexibility and crack-bridging capabilitiesNo lateral water migration between the concretestructure and the membrane system▪High watertightness tested according to variousstandards▪Fully and permanently bonded to the reinforced concretestructure▪Resistant to aggressive conditions in natural groundwater and soil▪▪ Easy to install with fully adhered jointsTemporarily resistant to weathering and UV exposureduring construction▪Made up of non-recycled / virgin HDPE for long durability▪▪ Eco-friendly material▪ Sound anti-puncture performance▪ Adaptable to settlement and distortionCan be combined with other approved Sika® Waterproofing/ Joint Sealing Systems

Self-adhesive modified bituminous membrane for post-applied below ground waterproofingDESCRIPTION SikaShield® E50 HDPE SA IN 1,5 mm is a bituminous, self-adhesive, fully bonded, post-applied, waterproofing sheet membrane with a thickness of 1.5 mm. It consists of a cross-laminated HDPE film that is precoated with an SBS modified bitumen compound. The underside has a removable liner over the adhesive compound for easy application. SikaShield® E50 HDPE SA IN 1,5 mm membranes must be protected with screed, reflective coating, drainage boards, or protection boards to protect from UV or damages from backfilling. USES The Product is used as a waterproofing membrane for: ▪ Basements and other below ground structures Horizontal reinforced concrete slabs, decks, podiums and protrusions ▪ ▪ Vertical reinforced concrete walls ▪ Single and strip foundations ▪ Extensions and reconstruction works CHARACTERISTICS / ADVANTAGES ▪ Used in versatile applications from basement to roof Cold-applied and self-adhesive (no heating or open flames required) ▪ ▪ Easy and fast application ▪ Fully bonded ▪ No special equipment required for application Good resistance to all natural aggressive substances in groundwater and soil ▪ ▪ Good electrical resistance ▪ Good resistance to ageing, tearing and perforation ▪ Excellent adhesive property and ▪ Dimensionally stable ▪ Good flexibility even at low temperatures 

Fosroc Membrane HDPE -P (Smooth) RF is a HDPE membrane with a release fi lm over pressure sensitive adhesive which allows poured concrete to bond fully with the membrane. Fosroc Membrane HDPE-P (Smooth) RF provides water, water vapour protection to water excluding structures and protects concrete from aggresive ground salts, chemicals and hydrocarbons. Fosroc Membrane HDPE-P (Smooth) RF is supplied with a self adhesive selvedge along one side of the roll to provide sealed laps and a comprehensive range of auxiliary products to simplify the application process. 

APP Waterproofing is comming in 3 mm , 4 mm thick. And SBS self adhesive waterproofing comes on 1.5 mm thick.