Venus Enterprises

Auramix 200 is a high performance superplasticiser intended for applications where high water reduction and long workability retention are required, Advantages   Low viscosity suitable for pumping of different grades of concrete to higher floors   Can also be utilized for high strength and high performance concrete   At high dosage it does not have high retardation effect   Higher E modulus   Improved adhesion to reinforcing and pre-stressing steel   Better resistance to carbonation   Reduced permeability   Better resistance to aggressive atmospheric conditions   Reduced shrinkage and creep   Increased durability Standards compliance Auramix 200 complies with IS:9103 , BS:5075 and ASTM-C494 Type 'G' . Description Auramix 200 is a unique combination of the latest generation superplasticisers , based on special polymers with long lateral chains. At the start of the mixing process this special polymers develop an electrostatic repulsion which greatly improves separation and dispersion of cement particles .This mechanism considerably reduces the water demand in flowable concrete. Auramix 200 combines the properties of water reduction and workability retention. It allows the production of high performance concrete and/or concrete with high workability retention. Auramix 200 is a strong superplasticiser allowing production of consistent concrete properties around the required dosage. Technical support Fosroc provides a technical advisory service for on-site assistance and advice on mix design, admixture selection, evaluation trials and dispensing equipment. Properties Appearance : Yellowish to Brownish liquid pH : Minimum 6.0 Specific Gravity @ 27 0C : 1.03 - 1.07 Chloride content : Nil (As per BS:5075 Part I) Alkali content : Typically less than 1 g Na2O equivalent / litre of admixture. Dosage The optimum dosage of Auramix 200 to meet specific requirements should always be determined by trials using the materials and conditions that will be experienced in use. The normal dosage range is between 0.5 to 2.5 kg/100 kg of cementitious material. Use at other dosages Dosage outside the normal range quoted above can be used to meet particular mix requirements. Contact Fosroc for advice in these cases Effects of overdosing Over dosage may cause delay in the setting time (but better than conventional SNF based admixture ) and segregation. Packaging Auramix 200 is available in 200 litre drums and bulk tanker. Storage Auramix 200 has a minimum shelf life of 12 months provided the temperature is kept within the range of 20C to 500 C and stored in unopened containers. If temperature of the product fall outside this range then contact local Fosroc office for advice.

MOULD RELEASE AGENT DESCRIPTION Ready to use low viscous mineral oil based mould release agent. Ready to use and easy to apply. USES Sika® Separol Plus can be used on moulds to obtain clean and smooth concrete surface and it’s use facilitates fast and easy removal and cleaning of: ▪ Steel formwork ▪ Plastic formwork ▪ Timber formwork ▪ Aluminium formwork ▪ Heated formwork CHARACTERISTICS / ADVANTAGES Sika® Separol Plus when used, provides following beneficial properties: ▪ Forms stable thin film when dried up ▪ No dirt sticks on surface after it is dried ▪ Clean, fast and easy stripping of formwork ▪ Extended life of formwork Improved finish stain and air-hole free fair-faced concrete ▪ ▪ Reduced concrete contamination ▪ High coverage ▪ Does not corrode steel ▪ Environment friendly product PRODUCT INFORMATION Chemical Base Blend of mineral/ Natural oils Packaging 230 litres Drums Appearance / Colour Brownish oily liquid Shelf Life 12 months from date of production if stored properly in original unopened, undamaged, sealed packaging. Storage Conditions Protect from frost, direct sunlight and contamination. Opened units should be stored closed. Density ~0.83 kg/l at 25°C APPLICATION INFORMATION Consumption Steel, Aluminium or Plastic formwork 40-60 m2/l and Timber form 30 m2/l. The consumption is dependant on the surface texture and porosity of the formwork. Actual dosage to be finalised on the basis of site trials.

Dr. Fixit Powder Waterproof is composed of waterproofing additives, dispersed in inert fine filler. It is an integral powder-waterproofing admixture used for waterproofing of concrete and cement plasters, because It makes concrete cohesive & reduces porosity & improve water tightness . Standard compliances / Specification } Meets the requirements of IS : 2645 – 75 standard Areas of Application } Basements, } Roof slabs and screeds, } Water retaining structures, } External plastering, } Bathrooms } Balconies. Features & Benefits } Corrosion - Chloride-free hence no chances of corrosion of reinforcement bars. } Water seepage - As an effective pore filler, helps to fill capillaries and pores to prevent water seepage. } Consistency - Makes the mix cohesive and denser, hence the concrete & plaster has reduced permeability . } Economics – Most economical water proofing additive, reduces water absorption. } Setting & strength - Does not affect the setting time and strength. Of the cured concrete. } Compatibility – Compatible with all types & grades of cements. Method of Application 1 HAND MIXING } Add Dr. Fixit Powder Waterproof to the dry mix of cement sand and mix evenly with a spade, until an even mix is obtained. } Add the measured quantity of potable water as per decided W/C ratio and mix to a homogeneous & uniform consistency concrete / mortars. } Place the mixed concrete / mortar into shuttering, provided } Cure the concrete / mortar surface as per regular practices of water curing. 2 MACHINE MIXING } Charge the Cement & sand as per the mix design into concrete mixer & mix for one minute. Add 500 g of Dr. Fixit Powder Waterproof for every 50 kg bag of cement. & mix for one minute. } Add the measured quantity of potable water as per W/C ratio and mix for 2-3 minutes to a lumps free homogeneous concrete. } Place the mixed concrete mortar into shuttering provided. } Cure the concrete / mortar surface as per regular practices of water curing.

MASTER PLAST SPL-19 is a high performance superplasticiser based on Sulfonated NaphthaleneFormaldehyde polymer design to allow considerable reduction of mixing water. It has a powerfuldispersing and deflocculating effect on the particles of cement. It increases the workability of concrete with an added advantage of high early and long term strength. It allows concrete to beeasily compacted with minimum vibrations.

Masterplast Flow 30 is a polycarboxylic ether based superplasticiser with very high waterreduction capacity The mechanism is based on steric hindrance effect. Due to the presence ofside chains linked to the polymer backbone it generates steric hindrance effect which greatlystabilizes cement particle’s capacity to separate and disperse. The specific configuration of PCEpolymer allows its delayed absorption on to the cement particles & disperses themefficiently

Water based, Acrylic emulsion curing compound for concrete and mortar Uses Provides a curing, sealing and dustproofi ng compound, which can be used in a wide range of applications:  High rise construction to eliminate water curing  Floors, warehouses, slabs and columns  Dustproofi ng concrete walls and fl oors  Clear sealer for concrete  Self-curing, primer system to subsequent coverings Advantages  Eco-friendly - water based, free from solvent, oils waxes, chlorinated or saponifi able materials  Excellent moisture retention for freshly placed concrete, resulting in minimising shrinkage cracks  Suitability for foot traffi c Versatile - can be applied equally well to freshly placed or existing concrete  Cost eff ective - can be over-coated with water based and solvent based acrylic coatings, epoxy coatings, polyurethane coatings. Standards compliance Concure AB Clear complies to ASTM C309 Type 1, Class B. Description Concure AB Clear is an acrylic polymer based non-degrading, single component curing compound. It is also suitable for use as a sealer and dust proofer for fl oors and walls. 

Non metallic, monolithic surface hardening compound Uses Nitofl or Hardtop Standard provide a highly abrasion resistant surface to concrete fl oors by the dry shake-on method which ensures that the hardwearing surface bonds monolithically to the base concrete. They are ideally suited for all industrial areas subject to the heaviest traffi c, e.g. loading bays, trucking lanes, car parks, workshops, machine shops, ramps and spillways. Advantages Non metallic - does not rust or stain.  Provides a hard, abrasion resistant surface  Forms monolithic bond with base concrete  Easy and economical to apply Description Nitofl or Hardtop Standard is quality controlled, factory blended powder which are ready to use on site. They contain special quartz-silica aggregates which have been selected for abrasion and wear resistant properties as well as shape and size. These latter considerations, together with the use of high performance workability admixtures, produces a material which is easy to trowel into the surface of fresh, wet concrete. Nitofl or Hardtop Standard cure monolithically to provide a dense, non-porous surface which is extremely hardwearing and abrasion resistant. Monolithic cure ensures that problems normally associated with thin ‘granolithic’ screeds, viz., shrinkage, cracking, etc., are completely overcome. Being non-metallic, Nitofl or Hardtop Standard provide a nonslip surface which will never rust and disintegrate.

Concrete Admixture Supplier, Cement Admixture Mumbai.
Organic Bipolar concrete penetrating corrosion inhibiting admixture. Uses: Auramix BCI is used as corrosion inhibiting admixture for all reinforced concrete and not limited to Below ground structure such as Pile, pile cap, mat foundation where chloride threshold value is more in the soil.  Bridges and fl yovers Structures in coastal areas and submerged conditions Power plants Steel plants High rise buildings Structures in sea water Pre-cast Elements Tunnels and underground structures Standards compliance Auramix BCI complies to various standards such as ASTM G1, JIS 1535(modifi ed), IS 9103 for compressive strength, AASHTO - T259, ASTM G3 for steel bars embedded in concrete, ASTM G109*, ASTM G180 and ASTM C1582M. Advantages Auramx BCI is a low dosage admixture having  Nitrites free  Improves durability of the structure  Used as a admixture: Dosage is independent of anticipated chloride levels Ensures steel protection even in the hardened concrete Does not get consumed by cement hydration  No adverse eff ect on slump retention and compressive strength Independent reports tested to International standards 

PAR Plast - LW is an integral liquid waterproofing admixture for concrete and cement mortar. It has good plasticising properties, makes concrete cohesive .

“MAGNICRETE MAGNIGROUT” is General Purpose High Strength Cement based grouting material designed to transfer load effectively, ensuring grouting precision and durability of structure. “MAGNIGROUT” inhibits corrosion of embedded steel and imparts high initial and ultimate flexural and compressive strength.

Water reducing & retrading admixture for concrete PAR PALST SPLV is a highly effective, water reducing liquid admixture with no added chlorides. it provides a singnificant improvement in workability without any bleeding & segregation.

concrete block and mortarprecast and reinforced concretebrick laying mortar mixesTremie concrete for moderate pours

BENEFITS < Ready to use, factory controlled < Eliminates on-site mixing < Provides dense, non- porous surface on application < Hard wearing, abrasion resistant < Monolithic bond with the base concrete < Non dusty and non slip surface < Facilitates easy cleaning < Long life and low maintenance < Available in various colors < Non-metallic and iron free - does not rust. PRODUCT USES < < < DESCRIPTION FAIRTOP STD is supplied as a monolithic industrial flooring compound ready to use factory controlled, dry shake cementitious system blended with special aggregates, selected for high abrasion and wear resistance and additives. FAIRTOP STD is used to obtain a dense, tough, abrasion resistant industrial floor with non dusty and nonslip characteristics. For extremely heavy flooring 12 mm thick FAIRTOP HD ready to use monolithic floor hardener is recommended. (A separate data sheet is available on this product.) FAIRTOP STD is a cementitious industrial flooring compound which creates a monolithic bond with substrates. FAIRTOP STD can be used in Loading bays, Factories, Warehouse, Car Parking areas, Truck Lanes, Workshops, Garages, Subways, Power Stations & Abattoirs. Recommended for refurbishment over terrazzo, Quarry or ceramic tiles. Also, recommended for workshops, show room, food & beverage processing areas to withstand moderate to heavy traffic. PROPERTIES Abrasion Resistance : FAIRTOP STD has been tested with funditor abrasion machine using Silicon Carbide Wheels. The sample was tested for 10,000 revs at a fixed speed and the amount of wear assessed by measuring the depth of the groove by abrasion wheels at four points around the perimeter. The results show that FAIRTOP STD improves the abrasion resistance compared to grano by over 150%. (as per IS 1237 : 1980) Compressive Strength : The FAIRTOP STD cubes when tested for compressive strength have typical strength of over 600 kg/cm² at 28 days. Mho's scale hardness of FAIRTOP STD aggregates between 7 to 8 scale. Colour Range : Presently available in Natural Grey, Brick Red and Green. APPLICATION INSTRUCTIONS Base Concrete : The base concrete should have a minimum cement content of 300 kg/m3 with a slump of 40- 60 mm with a low water cement ratio. Method of Laying Base Concrete : The base concrete must be laid in accordance with good concrete practice either in bays or long strips. Particular care must be taken at the corners and edges of the bays to obtain good compaction and to maintain level for subsequent troweling operations. If too much of free water is seen on the surface, subsequent water content in concrete must be reduced to obviate the presence of free water. APPLICATION As a guide, the application should be made between 1 hour2 hours, i.e. when the surface water on concrete is completely evaporated. (When tested with Thumb, it leaves an impression but concrete does not stick to the Thumb). The application is made in two stages: Divide the floor in equal no. of bays. As soon as the concrete becomes tacky, make 150 to 200 mm strip on edges. Spray the material on these strips with dry shake. Apply the power Floater for a nd compaction and to get moisture on top. 2 application will be in perpendicular to first application. In one of the bays, when edges are covered with dry shake, start spraying / spreading material in mid strips. After 12 hrs. of application, this requires pond curing for a high strength, abrasion resistance floor. F

Plasticizers Super Plasticizers.

polymeric super plasticizers are known for improving the workability of concrete by reducing the need of water.

Masterplast MF is a innovative multipurpose super plasticizer based on modified Polycarboxylic ether. The product is specially developed to meets the requirements of paver blocks industries,buildings blocks, fly ash bricks and semidry concrete products. The product also can be use to reduce the water demand of the mixes. It has the advantage of producing very high early strengths and thus makes the material suitable for use in precast concrete applications and in areas where fast shutter stripping are required. The product improves mix rheology and reduces the cycle time due to its setting time acceleration property 

MASTER PLAST SPL-1 is a Superplasticiser with high strength properties based on Sulphonated Naphthalene Formaldehyde polymer. It is a liquid plasticizing admixture for cement and mortars. It has a powerful dispersing and deflocculating effect on the particles of cement. It makes the concrete flowable with an added advantage of high early and long term strength. It allows concrete to be easily compacted with minimum vibrations. FEATURES / ADVANTAGES  It controls the rate of setting of concrete and mortars.  It improves workability and easier handling.  It does not contains chloride hence does not corrode reinforcement.  It can be used even for fly ash and slag cement concrete.  It retains the workability of concrete.  It reduces shrinkage and permeability of hardened concrete.  It eliminates formation of cold joints between subsequent pours in mass of structural concrete  It increases the strength of concrete due to its water reduction property. USAGE  It is widely used in ready mix concrete  It is particularly recommended for concreting in hot climates, long or difficult pours prestresed concrete in large sections or mass concreting.  It is used more specifically in - Pavement concrete, Pumped concrete, Structural concrete, Bridge decks, highway concrete, Long distance transporting, precast concrete. 

DESCRIPTIONSikaPlast®-5203 NS is the latest development of superplasticizerfor concrete. It meets the requirements forhigh range water reducing superplasticizersUSESSikaPlast®-5203 NS is a unique multipurpose superplasticiserthat is particularly suitable for the productionof ready mixed concrete. Additionally it provideshigh water reduction and improved fresh concretecharacteristics.With its outstanding cost / performance SikaPlast®-5203 NS is used for the following:A wide range of applications where excellent workabilityis requested▪▪ Concrete with high water reduction▪ High efficient concrete applicationsVariable use in different concrete systems with differentraw materialsCHARACTERISTICS / ADVANTAGESSikaPlast®-5203 NS is a powerful superplasticiserbased on advanced technology which gives the followingadvantages:Strong water reduction, resulting in high density,high strength and reduced permeability▪Less sensitive against variations in aggregates and /or different cement types▪▪ High efficiency even at low dosage ratesExtended workability in conjunction with subsequentstrength development▪Superior plasticising effect, resulting in improvedflow, placing and compaction characteristics

PAR PLAST RHV is a solution admixture and additives in water. It is a specially formulated for combined action as water reducing agent with accelaration in setting time. when added to the concrete mis it gives a good workability & heil to set faster than regular conventional concrete in the fresh state and high early and ultimate strengths in the hardened state.

High performance concrete used for columns, beams, decks & dams.Low temperature concrete precast concrete General purpose concrete requiring high strength High strength & low premeable concrete under water comcrete Tremie concrete concrete brick / blocks manufacturer

PAR PLAST SPL
Water reducing & retrading admixture for concrete PAR PLAST SPL is a highly effective, water reducing liquid admixture with no added chlorides. It provides a significant improvement in workability without any bleeding & segregation.

SPECIFICATION :
Meets the requirement of IS:9103 - 1999 and ASTMC- 494-86, Type B & D.

AREA OF APPLICATION:
• Concrete block and mortar
• Precast and reinforced concrete
• Brick laying mortar mixes
• Tremie concrete for moderate pours

FEATURES & BENEFITS:
• Reduces water upto 20 %
• Improves workability at a given w/c ratio
• Provides highly cohesive concrete mix without any bleeding and segregation
• Helps in reducing cement content for a required strength

METHOD OF APPLICATION:
The correct quantity of PAR PLAST SPL should be measured with recommended dispenser and should be thoroughly dispersed with approx. 5 - 10 % of the recommended water content (based on mix design by weight.)Mix concrete constituents along with balance approx. 90 - 95 % of the recommended water content (based on mix design by weight) for 3 minutes. As soon as step 2 is over, the admixture dispersed in water (as in step-1) is to be added to the wet concrete and mix it further for2-3 minutes to get a homogeneous mix.

TECHNICAL INFORMATION :
Colour: Dark Brown
Sp. Gravity: 1.19 ± 0.04 at 30OC
Chloride Content: Nil
Base : Sulfonated Napthalene Formaldehyde
Dose: Upto 750 ml/ 50 kg bag of cement

PACKING: 20 Kg ,60 Kg & 250 Kg

MasterPlast BS-3 is chloride free water reducing admixture, formulated specially for applications in concrete block industry. It is effectively used to improve the quality of hollow blocks, paving blocks, etc. FEATURES / ADVANTAGES  It improves the cohesion and hence it imparts excellent finish.  It improve

MASTER PLAST SPL-8 is a Superplasticiser based on Sulfonated Naphthalene Formaldehyde Polymer with high strength properties. It is a liquid plasticizing admixture for cement concrete and mortars. It has a powerful dispersing and deflocculating effect on the particles of cement. It makes the concrete flowable with an added advantage of high early and long term strength. It allows concrete to be easily compacted with minimum vibrations. FEATURES / ADVANTAGES

Superplasticizers, also known as high-range water reducers, are chemical admixtures that significantly improve the workability and flow properties of concrete mixes. They allow for a reduction in the water-cement ratio, leading to increased strength and durability without compromising workability. 

MASTERPLAST HPA 3 is a polycarboxylic ether based superplasticiser with very high waterreduction capacity. It is mainly developed for meeting the criteria of self compacting concrete withhigh early as well as long term strength at lower water cement ratio. The mechanism is based onsteric hindrance effect. Due to the presence of side chains linked to the polymer backbone itgenerates steric hindrance effect which greatly stabilizes cement particle’s capacity to separate anddisperse. The specific configuration of PCE polymer allows its delayed absorption on to the cementparticles & disperses them efficiently.

PAR PLAST SPL
Water reducing & retrading admixture for concrete PAR PLAST SPL is a highly effective, water reducing liquid admixture with no added chlorides. It provides a significant improvement in workability without any bleeding & segregation.

SPECIFICATION :
Meets the requirement of IS:9103 - 1999 and ASTMC- 494-86, Type B & D.

AREA OF APPLICATION:
• Concrete block and mortar
• Precast and reinforced concrete
• Brick laying mortar mixes
• Tremie concrete for moderate pours

FEATURES & BENEFITS:
• Reduces water upto 20 %
• Improves workability at a given w/c ratio
• Provides highly cohesive concrete mix without any bleeding and segregation
• Helps in reducing cement content for a required strength

METHOD OF APPLICATION:
The correct quantity of PAR PLAST SPL should be measured with recommended dispenser and should be thoroughly dispersed with approx. 5 - 10 % of the recommended water content (based on mix design by weight.)Mix concrete constituents along with balance approx. 90 - 95 % of the recommended water content (based on mix design by weight) for 3 minutes. As soon as step 2 is over, the admixture dispersed in water (as in step-1) is to be added to the wet concrete and mix it further for2-3 minutes to get a homogeneous mix.

TECHNICAL INFORMATION :
Colour: Dark Brown
Sp. Gravity: 1.19 ± 0.04 at 30OC
Chloride Content: Nil
Base : Sulfonated Napthalene Formaldehyde
Dose: Upto 750 ml/ 50 kg bag of cement

PACKING: 20 Kg ,60 Kg & 250 Kg

Choksey Accelerating Admixture For Concrete Masterspeed ACL, For Construction, Packaging Type: Bucket. Master speed – ACL is a liquid accelerating admixture for cement concrete & mortar. It is designed toaccelerate the normal setting time of concrete.

SILICO Flow is a dry ready mix cementitious based product formulated for use in repairs/restoration of areas where the concrete is damaged. It can be used were movement is restricted and it is dicult to pour/place conventional concrete in the area to be repaired. SILICO Flow meets the requirements of GreenPro Ecolabel and qualies as Green Product. 

Asian Paints SmartCare Tile Grout - Epoxy Based is a two component epoxy resin based tintable grout specifically designed for use in application of ceramic tiles, vitrified tiles and stone joints where a hygienic and sterile condition is expected. Specifications 2 Component epoxy based, easy to mix joint filler available in 26 brilliant shades Impervious Impervious ensuring excellent waterproofing in wet areas Excellent adhesion Excellent adhesion – sustainable and durable up to the life of the tile Hygienic Ideal for areas where hygiene maintenance is critical like Laboratories, Breweries, Clinics and Bathrooms Chemical Resistance Non-toxic and Chemical resistant

RITEBLOCK  PC is a ready to use, new generation plasticizer based on new polycarboxylate technology and specially designed to make unreinforced plain concrete block cost efficient. High performance compaction aid for semi-dry/no-slump concrete.

Concure WB is a white, low viscosity wax emulsion which incorporates a special alkali reactive emulsion breaking system. It is supplied as a white emulsion which forms a clear film on drying. This system ensures that the emulsion breaks down to form a non penetrating continuous film immediately upon contact with a cementitious surface. This impervious film prevents excessive water evaporation which in turn permits more efficient cement hydration, thus reducing shrinkage and increasing durability. Once formed, the membrane will remain on the concrete surface until eventually broken down and eroded by natural weathering. Where it is required to apply a further treatment to such concrete surface, it may be necessary to remove the membrane remaining after curing by wire brushing or other mechanical means

CEMENTITIOUS NON-SHRINK RAPID SETTING MULTIPURPOSE MORTARDESCRIPTION MASTERPLUG-3 is a fast sealing cement based product formulated with selected additives. It sets very fast within a few minutes. It is used in a situation where very quick setting is required. It is effectively used for stopping the flow of running water. It is an ideal material to stop leakages prior to the application of waterproof renderings in basements. FEATURES / ADVANTAGE  It is ready to use product and requires only the addition of water at site before plugging and sealing cracks.  It sets very rapidly thereby, stops leakages.  It stops running water, reducing damage.  It is cementitious product and hence it is economical.  It can be used where quick setting under water is required.  It is non-shrink as it expands on setting.  It bonds to the substrate very well.  It does not affect RCC as it is free from chloride.TYPICAL APPLICATION  Used for leak-plugging in running water.  Used in all places where quick setting is required.  Used for all plugging work, quick repairs of concrete, screed, plaster and brick work.  Used for basement and manhole repairs.  Used for concrete pipes repairs.  Used for anchoring of bolts and hand rail setting

Integral sealing for construction joints in concrete cast insitu. Convenient and problem solving in situations where a conventional waterstop would section elastomeric strips Size : 10mm X 20mm Solids content : 100% Unrestrained volumetric expa

Dr. Fixit Pidipoof LW is specially formulated additive composed of cement compatible, surface active agent, polymers & additives. It is used as an additive for cement concrete/ mortar/ plasters, because plastisizingproperties, makes concrete cohesive and prevents segregation. It improves the integral waterproofing properties of cement concrete 

Master Plast SPL-8 is a Superplasticiser based on Sulfonated Naphthalene Formaldehyde Polymer with high strength properties. It is a liquid plasticizing admixture for cement concrete and mortars. It has a powerful dispersing and deflocculating effect on t

For fast demoulding of pavers
PARPAVER, a specially formulated product reduces the setting time of cement so that the pavers can be removed from mould earlier.



ADVANTAGES

• Reduces the setting time and help achieve high early strength.
• Highly cost effective,

CHARACTERISTICS
State : Liquid
Colour : Colourless to Pale Yellow
pH : 7 – 9
Sp Gravity : 1.30

GUIDELINES FOR USE
Dosage of 100 - 400 ml of PARPAVER per 50 kg bag of cement is recommended. The actual dosage has to be determined at the site.
1. Take 100 - 600 ml of PARPAVER and mix with 2 liters of water.
2. Prepare mortar with 50 kg cement bag.
3. Add 70% of water to the mortar and mix for 5 minutes.
4. Add PARPAVER solution to the cement mortar.
5. Mix thoroughly and ensure the solution is spread over the entire mortar.
6. Add water to achieve the required consistency.
7. Mix thoroughly and apply in normal fashion.

STORAGE :
Stable under normal conditions. Should be stored away from direct sunlight.

HANDLING :
Use of gloves and safety glasses is recommended.

PACKING :
Available in 20 kg and 250 kg

High performance PCE based admixture forwide range of concrete grades.UsesAuramix 200 is a high performance super plasticizer suitablefor low and high grade concrete and intended for applicationswhere high water reduction and long workability retentionsare  concreteproduction.Reduce rate of workability loss normally associated withsuper plasticiser. Reduces shrinkage cracking becauseof lower water cement ratio. Makes the concrete waterimpermeable.Better resistance to Carbon

DESCRIPTION MASTERPLAST PL-1 is liquid plasticizing admixture (additive) for cement concrete based on modified lignosulphonates. It reduces the water requirement for concrete mix to attain a given workability. It may be used to reduce cement content of concrete mix without affecting the strength. It is an economical s