Venus Enterprises

Nitoproof 100 is designed to provide a continuous barrier to the passage of water and water vapour and can be used to produce vapour barriers, damp proof courses, linings to potable water tanks and pipes, below ground concrete protection, concrete curing by water retention, and corrosion protection to metal surfaces. Advantages ! Single component ! Easily and inexpensively applied; high coverage rate ! Tough and resistant to most naturally occurring chemicals ! Does not taint water ! Can be applied to damp concrete substrates ! Quick drying ! Excellent adhesion to most common building substrates ! Excellent water retention for use as a curing compound ! Successfully used for over 30 years in a wide range of environments Standards compliance Nitoproof 100 complies with BS3416:1975 Type 1A General purpose bituminous coating, BS3416:1975 Type II Bituminous coating for drinking water tanks and ASTM C309 water retention requirements for curing membranes. Description Nitoproof 100 low viscosity blend of selected bitumens in solvent dries to form a high quality tough bitumen film. Nitoproof 100 can be applied by brush, roller or spray equipment to prepared surfaces for a variety of purposes. Properties Test method Typical result Drying time : BS3900:C2:1972 21/2 hours Flexibility : BS3416:1975 Pass Chloride protection : BS3416:1975 Pass Effect on water : BS3416:1975 Pass Appendix B Overcoating time : 3 hours (min) Instructions for use Preparation Surfaces must be clean, dry, free from oil, grease and all loosely adhering particles such as rust, mill scale, mortar and cement laitence. These should be carefully removed by wire or stiff brushing and finally soft brushing or filtered compressed air to remove dust. Oil and grease should be removed by the use of a proprietary degreasing agent. For optimum adhesion to steel, grit blasting to SA21/2 is recommended. Nitoproof 100 can be applied to damp concrete, brick and plaster surfaces provided there is no free surface water or bleed. A test patch is recommend where there is doubt. Application Stir thoroughly prior to use. Damp-proof membranes, vertical vapour barriers Apply a full coat of Nitoproof 100 and allow to dry. Coverage rate should be approximately 3m2 per litre. Apply a second coat of Nitoproof 100 at right angles to the first coat. Water tank and pipe line protection Two coats of Nitoproof 100 should be applied as detailed above. Where necessary the coating can be thickened at floor/wall corners by forming a 20x20mm fillet onto the first coat of Nitoproof 100 and liberally coating with a second coat of Nitoproof 100. Concrete screeds or render Where it is necessary to cover the membrane with a screed or render, clean grit 2mm nominal size should be broadcast into the wet second coat to provide a mechanical key. All loose grit should be removed prior to placing the screed/ render. (Care should be taken to ensure that the membrane is not damaged during placing of the screed). Curing compound Apply two coats of Nitoproof 100 as for damp proof membranes. This will give a curing efficiency in excess of 80% and comply with ASTM C309. Nitoproof 100 can be applied to damp concrete.

“Venus Enterprises”, are Sole Proprietorship (Individual), based company, engaged in Wholesale trading of Waterproof Paint, Construction Materials, Waterproofing Liquid and many more. Under the direction of “Shejal”, we have achieved the highest place in the industry. We also provide Coating Service, Crack S

Wire brush and clean the surface thoroughly to remove all dirt and loose particles. • Dilute ShaliKote® T-10 from its pasty consistency to light consistency by adding water in the ratio of 1:1. Apply this diluted material on the roof surface as primer. No dilution should be done in case of ShaliKote® T-10A. • When the primed surface is dry and has turned black from its original brown colour, apply ShaliKote® T-10 and allow the emulsion to break. It will turn black from its original brownish colour. • When the emulsion has set in, spread coarse sand or crushed stone chips over the surface. 

"MAGNISILK" has been formulated with specially designed best in class imported Polymers and Additives for providing more adhesive strength which provides a strong base, ensuring a longer life for the painted surface. It does not require water curing and it can even be applied on freshly plastered wall thus resulting in savings of time and cost. During repainting, the surface done up with "MAGNISILK" requires minimum scrubbing thus eliminating the mess of dust, which is a health hazard especially for asthmatic patients. •  Generally Primer is not required after application of "MAGNISILK" before Painting which reduces the time and cost of the additional application process. If applied properly there is substantial increase in the coverage of paint due to "MAGNISILK" water resistance properties and high quality. •  Its superior quality ensures that it meets the global standards of HDB, Singapore. FOR SILKY WALLS MAGNISILK “MAGNICRETE-MAGNISILK” for Silky Finish Walls – Freedom from Flaking and Saving on Paint. “MAGNISILK" is a water-resistant white cement-based dry mix powder which provides a strong base on concrete and plaster both on Internal and External surfaces and ceilings. It is applied after plaster and before painting of the wall. It fills the fine pores of the walls and ceilings, thereby providing a white, smooth and dry surface for painting. Being water resistant it provides a protective base to surfaces which prevents expensive paint from flaking. About Magnicrete Products Products under MAGNICRETE brand are produced in a State-of-the-Art Plant at Rajasthan in India with German Technology. It is one of its kind, most modern Dry Mix Plant of latest technology in the world with a capacity of more than 160K MT per annum. The plant is fully automatic including the raw material handling system, mixing of various raw materials to the finished products loading system and truck loaders. Fully computerised without any or least manual intervention. The plant is equipped with very high efficiency mixers and choppers for thorough and uniform mixing of ingredients with high precision, even with dosages as low as 0.01%. The plant operation runs automatically through most advanced Supervisory control and data acquisition (SCADA) System, through PLC in a close loop system of software and hardware elements. This allows to control processes, monitor and process real time data through directly interacting with equipments and devices like sensors, screws, motors etc., which effectively reduces the chances of manual operating errors and enable to produce world class quality Dry Mix products with precision and consistent quality for Magnificient buildings. The plant is supported by in-house research and development centre of international standard, fully equipped with excellent laboratory facilities including prototype German dry mix plant, for all critical and important quality tests. It is run and managed by well experienced senior professionals having proven work experience in the industry

ShaliBond® BS / CS is a cold applied bituminous adhesive for fixing waterproofing membrane. It is manufactured from special grades of bitumen, suitably blended with other additives. It has semiliquid consistency and is ready to use