Venus Enterprises

Bituminous Flashing Tape is a Self -Adhesive tape made of a Butyl & Bitumen Rubber Compund, Self Protected by re-enforced Aluminum Foil on one side and Adhesive side is protected by Release Film. Flashing Tape is a simple yet highly effective solution for waterproofing, sealing and insulation.

Uses:

• Roofs - around chimneys and skylights, over joints/ cracks in tiles and roof cladding.
• Exterior walls - joints and cracks in asbestos cement sheeting, cracks under masonry ties and anchorages, around wall penetrations (such as water pipes), gutters and downpipes.
• Terraces - at joints between terraces and exterior walls, joints in parapets, roof edges, sides, flashings and joints. Inside the house - leaking pipes, showers etc.

Note: The Prices of the product varies as per the drawing ,design, dimension & specification of product.
Additional Information

Renderoc Wallputty can be used as mentioned below:  Interior walls  Exterior walls  Fresh wall as well as repainting of walls  Concrete blocks and panels  Aerated light weight blocks  Plastered brick and block wall  Precast walls & ceilings Advantages  Smooth and glossy white fi nished surface   Provides ideal base as a primer for painting.  No curing required post application.  Low VOC.  Excellent workability which makes ease for application.  Suitable for interior as well as exterior.  Accepts any kind of paint or distemper application on it.  No peeling, fl aking or blistering & improved life for paint fi nishes. Description Renderoc Wallputty is a perfect blend of white cement, special polymers and minerals which protects & smoothens walls and is especially suitable for all types of cementitious surfaces like concrete, rendered wall, blocks and panels, precast walls & ceilings and plastered surfaces. The product being pure white in colour, any shade of paint comes alive on it and starts refl ecting its true tone. It has strong adhesive properties which provides a powerful bond between the base and the paint, making it an ideal subsurface for all interior, ceiling and exterior walls ensuring a longer life for the painted surfaces. Technical Support An experienced technical advisory team is available to give technical service on request. Properties Sl No Requirements Test Method Specifi cation 1 W/P ratio - 0.30 - 0.40 2 Wet Density - 1.5 - 1.9 gm/cc 3 Bulk Density - 1.3 - 1.5 gm/cc 4 Setting Time (Initial) IS:4031 (part-5) > 30 min 5 Setting Time (Final) IS:4031 (part-5) < 600 min 6 Pot Life - > 90 min 7 Workability - Good 8 Chalking - No 9 Compressive Strength EN 1015-11 > 6 N/mm2 10 Dry Adhesion 14 days ASTM 4541 & EN 1015-12 Min 0.8 N/mm2 Note: The typical physical properties given above are derived from testing in a controlled laboratory environment. Results derived from testing fi eld-applied samples may vary, dependent on actual site conditions. Specifi cation Clause: Renderoc Wallputty shall be a prepacked material requiring only water addition for excellent workability which makes ease for application at site to get smooth and glossy white fi nished surface. The material should have self – curing properties. The product shall have compressive strength > 6 MPa and bond strength 0.8 MPa. Application Instructions: Surface Preparation: New surface requires preparation such as removal of dust, dirt and foreign matter. In case of cracks, voids and damages, recommend our repair products. If surface plaster is rough, apply white cement / white cement mortar and level the surface. Cure the surface for 2 days, before starting putty coat. Surface should be in just-wet condition, prior to putty application. If the surface was made by cement ghutai (smoothening) which normally is very smooth, bonding with putty may not become suffi ciently strong. Scraping the surface with emery stone/paper is recommended before putty application. Fosroc

An epoxy floor coating is a durable, protective, and decorative surfacing solution created by mixing an epoxy resin with a hardener, which then forms a strong, seamless bond with a substrate like concrete. It is widely used in industrial, commercial, and residential settings due to its longevity and resistance to wear and chemicals. Key BenefitsEpoxy floor coatings offer numerous advantages: 

• Durability and Strength: Highly resistant to heavy traffic, impacts, and abrasions.
• Chemical Resistance: Withstands exposure to various chemicals, acids, and solvents, making it ideal for industrial environments and garages.
• Easy Maintenance: The seamless and non-porous surface is easy to clean with a mop and detergent and resists stains and bacteria growth.
• Aesthetic Appeal: Available in a wide range of colors, finishes (matte, satin, glossy), and decorative options like flakes, metallic pigments, or quartz granules.
• Safety: Can be made anti-slip by adding aggregates to the topcoat, which is a key safety feature for commercial and industrial spaces.
• Waterproof: Once fully cured, epoxy creates a solid, non-porous barrier that effectively blocks water and moisture, making it suitable for basements and food processing plants.
• Cost-Effective: Due to its long lifespan (typically 10 to 20 years or more with proper maintenance), it is a cost-effective flooring option over time despite the initial investment. 

Single Component, Rapid Foaming and Setting Hydrophobic Polyurethane Nitofi ll PU 1F Uses Stops the fl ow of water when injected into cracks in concrete in the presence of dripping water. Nitofi ll PU 1F provides an eff ective system for crack sealing in wet conditions. Areas of application include : Defective concrete (cracked or honeycombed) Concrete joints, Limestone, Brick construction Pipe intrusions, Waste water tanks Tunnels, Dams, Subway (Metro), Sewers, Manholes, Utility boxes, etc. Soil stabilization Advantages  Negative side application possible  Deep penetration into very small cracks  Foam increases in volume to fi ll cavities and voids  Excellent bond to surfaces  Good adhesive strength, tolerant of movement  Inert after curing, constant volume, no shrinkage  Does not create new cracks Description Nitofi ll PU 1F is a hydrophobic grout based polyurethane. Upon contact with water, it reacts to closed cell rubber-like foam while expanding its volume up to 27 times. The cured material is of a constant volume. Since water is not a component of the foam structure, the cured material is essentially not aff ected by water or dryness. The reacted material does not shrink or swell. Depending on the pressure of injection, Nitofi ll PU 1F reacts to a very dense material or foam. Technical Support The company provides a technical advisory service supported by a team of specialists in the fi eld

FAIRFLO CRYSTALLINE significantly reduces the penetration of water and other liquids, ensuring optimal waterproofing and protection for concrete structures. This integral crystalline capillary waterproofing admixture is seamlessly incorporated into the concrete mix during batching. Its specialized additives react with the moisture in fresh concrete and the by-products of cement hydration, catalyzing a transformative chemical reaction. As a result, a non-soluble crystalline formation is generated within the concrete’s pores and capillary tracts, permanently sealing it against the penetration of water and other liquids.

Features

• Hairline Crack Sealing: With its remarkable capabilities, this admixture can seal static hairline cracks up to 0.5 mm in width.
• Hydrostatic Pressure Resistance: It offers outstanding resistance to both positive and negative side hydrostatic pressure, safeguarding concrete against potential damage caused by water pressure.
• Protection Against Harsh Substan- ces: The admixture provides reliable protection against sewage and industrial wastes, preserving the integrity of concrete in environments prone to chemical exposure.
• Integration with Substrate: Once added to the concrete mix, FAIRFLO CRYSTALLINE becomes an integral part of the substrate, enhancing the concrete’s waterproofing properties on a permanent basis.
• Resilience to Chemical Attack: With its high resistance to aggressive chemicals, it ensures the longevity of concrete structures even in chemically challenging environments.
• Breathability: While effectively water- proofing the concrete, it allows the material to breathe by enabling the passage of water vapor, preventing moisture build-up within the structure.
• Safety and Environmental Consciou- sness: This non-hazardous and non-toxic admixture prioritizes safety of workers and the environment, offering peace of mind during construction.
• Flexibility in Construction Schedu- ling: The product’s ability to be added during batching eliminates climate restraints, increasing flexibility in construction scheduling.
• Reduced Permeability: By reducing concrete permeability, this admixture effectively prevents water and harmful substances from infiltrating the concrete, enhancing its longevity and performance

Reckoned as one of the eminent business names, we are readily engaged in the arena of presenting to our customers Enamel Paint Coating Service. A team of nimble personnel implements these services in tune with pre-defined provisions of clients. As well, we provide these services to our clients with utmost care to best match up with the prospects of our clients.

Features Benefits:

• Water borne single-pack, low odor, rapid drying paint
• Kills or inhibits the growth of harmful bacteria such as escherichia coli and staphylococcus
• Excellent stain and scrub resistance
• Easy to apply with conventional tools
• High mechanical robustness
• No fungus, algae, mildew growth on the cured paint film

SC Apcorep Corproteck System which is a self healing coating system for structural steel that provides a unique feature of passivation of pinholes by redox mechanism for corrosion protection. This 4 coat system protects structural steel against chloride ions, Sulphur di-oxide, corrosive elements, acidic environment and thereby improves life of steel members drastically

WATER AND OIL REPELLENT, ANTI-STAINING AND ANTI-GRAFFITI TOTAL PROTECTION FOR ALL POROUS BUILDING SUBSTRATES .ProtectGuard® is the leading product for all-round protection for all porous building materials. This one product delivers water and oil repellent protection and anti-graffiti protection for porous building materials. ProtectGuard® helps tackle the deterioration caused by atmospheric pollution, grease-type staining, penetration of liquids and graffiti. A surface treated with ProtectGuard® will benefit from an increased lifespan and will be easier to maintain. ProtectGuard® is a non film-forming impregnation product that leaves the treated surface permeable to air and water vapour. ProtectGuard® is completely colourless after application and does not change the appearance or the composition of the treated surface. It is also UV-resistant and does not discolour with age.